I keep reading that the sway bar/stabilizer bar bushings on the L322 full size are not replacement by themselves as they're apart of the entire bar unit and must be replaced together. Is this just the earlier models? I have a 2008 and I was able to buy the sway bar bushings separately, although...
Does anyone have recommendations for an aftermarket brand that’s equal or better quality than the Genuine Land Rover Sway Bar Bushings and End Links?
I’ve seen a lot of these parts from Eurospare, Centric, Febest, Moog, Britpart, Mevotech, Lemfoerder. Etc..
The Genuine Land Rover branded are...
Hi just bought oem front/rear sway bar bushings for my 2007 RRS HSE 4.4 (regular suspension)
Two years ago bought the cheapest bushings on ebay (front & rear) and handling improved but after few months was back to feel very loose
Lesson learned, this time want to install the oem with correct...
Has anyone had this issue? The bolts that hold the sway bar are corroded and will not come off. They have been heated, oiled, lubed, everything. I have had 2 places tell me my only option is to remove the engine or drop the subframe. Engine removal is not an option as I am not dumping 4k for a...
Hey all,
I recently took a trip to Waterloo, South Carolina, USA to Gulches ORV Park. My P38 has been converted to coil springs and has approximately 31.4" A/T tires on it.
Before this trip, I would get a slight vibration around 65-70 mph, and then it dies off at 71+ mph. At the ORV park this...
I am replacing the links and bushes for the front sway bar. Having replaced most of the rest of the steering components in the last year and since it is cheap and easy to do, I decided to do this as well. I ran into a small snag. The upper mount for the link, ANR3304, is so recessed that I...
For those of you that are like me and hate the tiny differences in the pictures we see on the net when trying to purchase Genuine Land Rover parts, here are some pics and the price I pad CDN for my 2010 Range Rover Sport Supercharged.
Hope this helps
P.S. That little notch in the middle just...
Hey guys to change the rear sway bar bushings would I need to have the entire back end jacked up or can I do it by just jacking up one corner at a time?
I have a 2007 RR Sport Supercharge. Both Sway bars are leaking oil badly and require replacing. It I change the air suspension over to the spring kit, can the sway bars be removed?
many thanks in advance.
So I wanted to get rid of the clunking sounds over small bumps on the road- Replacing the passenger side was pretty easy, but the driver's side top nut was... quite a peach.
Combination of multiple 12 point 18mm wrenches, then a shallow 19mm socket and extensions I was able to get it out and...
Hello all...noticed my Driver's Side Front Sway Bar Link has popped off on the top. The part is as shown below, where the metal end with the white cap is not in place on top but the bottom one is fully intact. This allows the metal "barbell" to swing freely 360* around. My question is, can this...
Hi i want to replace front sway bar links on my rrs hse 2007
The car has to be level on jack stands or can be done lifting one corner at a time with a jack ?
Thank you
Didn't have much luck searching for an answer to this specific question...
I've got a 2010 RRS HSE without DR.
I've managed to replace the sway bar bushings at all four corners except the driver side front. That top nut is quite a pain to get to. Does anybody have advice on what tools/tricks...
My 15 ATB Dynamic makes a pretty pronounced groan/creek sound when going up a driveway or or speed bump at an angle. The dealer says this is normal and it's the sway bars unlocking. This is so noticeable I cannot imagine it was intended to be this loud. Does anyone else have this?
Got a quote to replace the front lower control arms (LCAs) and front sway bar bushings with new parts from a local indie shop here in Nebraska. They were very knowledgeable about the Sport (owner's wife has one apparently) and I was in agreement with his recommendations. He told me it would be...
Hi I have a 2006 supercharged 4.2. I replaced the right front air shock with an after market product made by arnott. The part went in fine and the compressor filled it with air. While taking off the sway bar extension one of the bolts stripped out. I had to order a new one. Put it back...
Hello all, Ive been chasing down an annoying clunk and the last option it can be is the sway bar bushings/end links. I've replaced upper control arms, lower control arms, tie rod ends, and ball joints. Steering feels tight and the only think I hear is a clunk over uneven pavement and its driving...
My bushings , replaced 25,000 kms ago have been squeaking on every bump and stop for a couple of months now.
Yesterday I dropped the skid plate and squirted with the little red tube on the cans, three kinds of stuff into them.
Lithium grease, Silicon lube, and Release all. Bombed both inside...
Hi,
I want to improve on road handling of my rangie. I tow a van on the highway (see pic), as well as daily driving duties around town. The under-steer is pretty woeful, it always was pretty poor. I know that certain aftermarket companies provided rear anti sway bars for the P38. From my...