Search Results for ‘size’

Hi everyone, I've recently bought a 1990 Range Rover Vogue and I'm tossing up ideas on tyre sizes with a 2 inch lift. Preferably 245/75r16. If any one is running these with a 2 inch lift please post some photos! Cheers.

I’m wanting to throw a 2 inch lift on my already coil converted P38. What size tires can I run / are those that have a 2 inch lift running? Currently on 265/60/r18’s (30.5” diameter); and I’d be going to 16’s. Preferably as big as I can without rubbing / cuts OR minimal rubbing / cuts.

All, Seems in a few weeks of driving the Rover, my daughter figured out how to blow the factory sub in the liftgate. Does anyone who the size of the sub or have a recommended replacement that is a direct replacement for the woofer itself? Thanks

This Full Size looking tough! 8) What do you guys think?

Hello everyone, Just wanted to share with you one of our inventory sets. Wheels Spec Wheel: Velos VXS02 Configuration: 1 Piece Monoblock Size: 24x10 Finish: Brushed Triple Dark Gloss Please contact me if you are interested. You can reach me via DM, email ([email protected]) or by...

So long story, but bottom line is I have successfully begun to cross thread my Radiator fitting where the upper trans cooling line attaches. I backed out eighth hopes of getting a Die and refurb the threads. Unfortunately I have a radiator where the port is braised on, and I can not take the...

Boots are disintegrated off the ball joints, but ball joints are still very tight. Want to just replace the boots packed with fresh grease. Can anyone indicate what size the boots are? https://polyboots.com/tie-rod-end-and-ball-joint-boot-14x31x23-mm-black-type-1

I was told today by three different vendors that the steel brake lines are no longer available for P38. What size steel line and fittings do I need for P38? Any sources in the US would be appreciated. I know where to get the tools for bending and making flares, but I need the actual raw material...

Hi all. On a L322 what is the permissible wheel size difference between front and rear axle? Currently have 255/50/R20 all round but must replace front two only. Will 265/50R20 be okay? Diameter is 30.43 inches (77.3 cm) as opposed to 30.4 inches ( 76.3 cm) Wheel circumference is 242.94 cm as...

Hi all, According to this thread the maximum wheel size that can be fitted on an L322 without modification is 285/55R20. That would be an overall wheel size diameter of 32.34 inches or 82.15 cm. They are hard to come by in my neck of the woods so I am interested in wheel size...

When I put the key in the ignition and turn the car on I get "Inspection 12.2004" I can't find anything in the manual or on line as to what this means.

Question for any IID Tool gurus here. I currently have the stock tire/wheel setup on my 2008 RRS HSE. 255/50/19. My IID Tool shows a Tire Radius value of (364) I am installing new tires which are 255/55/19. These are 1” taller over stock. Any experience on what value to change it to for the...

I recently purchased a 2016 full size RR.I feel like I searched every where for a tow hitch receiver assembly that I can install. I have found the one for the RR Sport at AB but have not had any luck finding one for the full size. Does anyone know if it exists? Or do I need to go to my...

can someone tell me what is the max tire size i can fit on this rim, currently it has 255/50 and which model year range rover this rim was fitted I want to know if it is a factory or aftermarket?

I’m budgeting for a lift and tires on my P38 and I am wondering if I’m going to need a spare tire carrier for the hitch. My question is what is the largest tire anyone has fit into the spare well inflated or deflated? The size I’m considering is 265/75R16, I don’t mind removing all of the foam...

Hello ! Lots of infos here, very interesting. 2009 L322 tdv8

I need to pull a small utility trailer. My RR did not come equipped with a factory tow bar. What are my best options? If factory $2800 my only choice? thanks in advance.

Hi all - hope someone can help with an issue that just starting happening today. I can't seem to find any help online with this one. With the car running and stationary I switch to manual mode then push the stick forward to go from 1st to 2nd as I do this I feel a slight bump or jolt. Manually...

Good evening, i have two doubts about GEMS oil cooling system, hope somebody knows the answer. 1) which is the real task of oil cooler bypass spring valve fitted in timing cover?Is this valve really so sensible to detect oil density, so when oil is cold (thicker) the valve open bypassing oil...