selector

Hello - Newbie here - I have done searches in forums, and looked for YouTube videos - closest answer I can find involves adjusting the shift cable, I hope that is it - My car is a 2013 Range Rover Sport HSE Luxury, with gas V8 and 6 speed automatic. It is American Spec, has 178k miles but was...

What's my RR trying to tell me? 4.6 Auto 1998 GEMS For the last few days, the gear selection light sometimes read differently from the physical position of the lever, but whatever the light says is also the reading on the dash. After the first time I saw it I put the battery on a trickle...

Hi All, I've been working on my 2003 RR L322. I'm in dire straits. Trying to change the Inhibitor Switch today. Rust on all bolts and nuts including center nut that mounts the gear change cable to selector shaft. This nut also holds protective plate over switch. Tried to remove the nut off...

That error code states to refer to test 24 of continuity test procedure. I have the workshop manual and rave and can never find information about which test needs to be done from when I get an error code from the on-board computer. In the past, I've been able to figure it you but this one has me...

So after a bunch of searching I’m still a little confused on the function the my new to me 90 SWB RRC Specifically I can only get the AC/ middle vents functioning. It seems the mode selector slider (?) which chooses between frees, recycle, and AC isn’t functioning since no matter it’s...

I've been looking at eBay.co.uk and noticed a number of 2012 L322 with the rotary gear selection setup and different Terrain Response selectors, like the ones in the 13+ LR4s, etc. What that just a UK option? Is it something that can be added later? I've never seen it in NAS trucks so I was...

I was under my 4.6 HSE yesterday to try and solve my inability to select P and 1 and discovered that the XYZ switch was installed very badly by Roger the Bodger, the last person who was fiddling there, and I need to consult the collective brain to repair the problems. First, the switch has a...

Hi all Just swapped the gearbox on mine as the oil pump had gone. The nut that holds arm on to the selector shaft has managed to disappear. Tried other nuts but cannot get anything to go on - didn't want to forced one. Anyone have any idea what the thread is? Thank Antony

2006 Range Rover HSE The tab from the selector switch broke off and I'd like to replace it. Ideally, I'd only like to replace the switch and not the whole console insert. Does anyone have a source for the high/low range selector switch? Does anyone have a quick guide for replacing the switch...

I have a 2004 L322 with 190,000 miles. I would like to sell it but nobody wants a truck that has this many issues. it knocks when cold cranking, I had to install the toggle switch to fix the dreaded steering column issue and now I have to pull on the gear selector to crank it. Its not my daily...

Hi all My front UJ propshaft broke and broke the sump, but it also also damaged the gear selector switch, bent the gear selector shaft upwards, rotated the bracket that holds the gear selector cable round by 45 degrees (shearing off the bottom bolt), and bent the gear selector cable/rod. I've...

Hi all, I've just replaced the front prop shaft after the old one broke free, dented the sump, smashed the gearbox oil pick up pipe and the gear selector switch. Replacement parts were ordered and all was going well until I tried to get the new switch fitted. It seems like the pin that comes...

Just bought a 1998 P38 diesel. Been searching the net for this but all I find is problems with the LCD-display which works fine on mine. My problem is one of the buttons on the temp-selctor. The left side is really hard to lower the temperature (getting the numbers lower). I have to press...

Don't like the smooth gear selector knob on my 2016 HSE...is it possible to buy the autobiography knurled gear selector knob, and how hard is it to switch them?

2005 L322 HSE with 118k miles Cant seem to find any threads on this. So the full chain of events were: 2 months ago, Air Suspension inactive (read codes, cant remember exactly but something to do with overworking the compressor I think, so thinking leak somewhere) Clear code Code came back in...

We have a 2008 Range Rover HSE with the 4.4 engine and 6 speed tranny. The gear selector has gotten stiff to move. We have not yet had any issues with getting into or out of gear. While at the dealer recently for an oil change, they recommended replacing some part of the mechanism under the...

My shifter keeps working lose, or the alarm is probably on a fritz. But frequently when I am driving the screechy alarm to indicate shifter out of selecetion comes on. Sometimes I just barely tap the shifter for the alarm to go off, sometimes I have to lean it into selected position for a moment...

Has anybody ever had an issue with their auto selector, (PRND321)? In a nutshell, everything is fine and the transmission does exactly what it should, kickdown and all. The problem I'm having, well more so an annoyance, is the colour indicator to show which gear has been selected. PRND321 are...

06 RRS 4.4 stuck in low range, blinking indicator and selector Hello All. This is a great forum and my first post. I have a 2006 RRS HSE 4.4 that I’ve owned since new. 73k miles. I love my RRS. I washed my engine bay and probably let water get in the area behind the battery where the...

The red LEDs indicting which gear is selected have stopped working on my 97 P38 4.6HSE. Gear position on the instrument panel works fine. Any ideas as to the cause?