seals

After a lovely day at Cars and Coffee, my rover decided it didn't like all that oil in the rear axle and spit some of it out the passenger side onto my wheel. I have read that this issue typically starts with a blocked breather. I crawled under the truck and did not see anything blocking the...

Hi there - just got a lovely 2011 white SC. Replacing of lots of little bits, broken clips and seals to be done. Looking for the rubber seals at the top of plastic pillar trims on each side of windscreen, where the plastic meets the roof, this doesn't show on the parts diagrams. Any clues? Does...

I sent in my 2003 4.4 for a vanos gear swap after running on bad seals for about a year. Now the mechanic says I need to replace my driver side head. Hes basically saying the bad vanos affected the cams and wore them down. He says its better to go ahead and swap out the entire head instead of...

People, since i've bought my range the driver door rubber seal its damaged, it has this cuts and tears. Searching around i found a couple of number parts, are these codes correct? (doesnt matter the door side?): LR013938 (Primary seal) LR014294 (Secondary seal) Due what i see are two...

I have a Vouge se 6 months old with sliding panoramic roof. The ends of the side seals on the roof look to have been eaten away about 25mm Long only on the off side seal. Also the center seal where the glass panel meet the same in the center. Anyone else had this problem?. Range Rover dealer...

Hello all. I have a 2001 Range HSE and was sitting in the car and heard a noise behind my dash. Steam started to come through my vents and it smelled like anitfreeze. I walked around the car to see antifreeze pouring out my passenger side door. Could this be my heater core itself or the seals...

Hi there, Does anybody ever met or have any information about this option for RRC OVERFINCH? I'm about to make upgrade for door soundproofing for my 95 LSE so any pictures, info or explanations would be appreciated. SECONDARY DOOR SEALS (38 Made from smooth, high silicone rubber, these...

Hi guys, I've been having starting issues with my p38.. When it's left overnight it turns over for a while before it starts, I've replaced the sender unit & pump, also put a none return valve just before the filter, replaced the leak off pipes.. However, I've just pulled the leak off pipe on...

The oil hoses to and from the oil filter assembly connect to the filter adapter plate on the left side of the block. The two hoses are secured to the plate with a single bracket. I have a slight oil leak there, enough to leave oil on the ground. I removed the plate & replace the O-rings...

I need a new pair of these. I had a pair ordered and paid for from ebay last year but that fell through. I've found a co called atkinson bespoke engineering in Birmingham who are selling pairs at £320 which is quite alot but as they are NLA from LR such is life. Has anyone used them or does...

Ok, I'm calling uncle/giving up on my ability to use the googles... I am trying to freshen up my GF's 97 HSE... and one of the items that needs some help is the Left Hand, Rear door seal.. the one that goes directly where the rear wheel arch is. It looks like in the trucks past, this seal got...

First post really enjoying the threads so thanks for all the great info on here. I have a 2009 RRS HST. 59k miles. Steering rack leaked right side boot. Sent the rack off to be rebuilt. Bleed system per Land Rover mech manual. Seal was still leaking. I sent it back for a second time and after...

I know much of the 2004 is BMW but not everything exactly. My oil filter assembly is leaking. Hard to tell just which line it is so I want to replace all O rings and gaskets on it. Are they all the same as on any one particular year and model BMW? I was assuming 2003 m62 X5. I can get BMW...

I had an awful lot of my front replaced by dealer -- hubs, brakes, etc. After all this dealer has replaced passenger side front axle shaft seal twice, but it still leaks. I've read all the posts on this forum but can't find a definitive solution to this very common P38 problem. Any further...

Hi, Ive recently replaced my rear cross-member and tailgate, the latter with a used bit from some scrapyard shelf, and the weatherstripping doesn't really jive. My RRC is a 92ish, and the tailgate had kind of chamfered parts at the bottom corners where the tailgate met the rubber, but the new...

I am contemplating doing the upper timing cover gaskets - I've heard from reading the lower don't usually fail but is it wise to just replace upper and leave the lower? Anyway, in the Rave manual, page 12-2-68 (211), under the refit section calls for a special tool and I'm having a hard time...

hi i am thinking about putting new seals in my compressor,you can buy them on ebay for pennies,but are they any good.anyone used them thanks.

In the model specifications of Rangerovers.net, the 2009 L322 model notes that they upgraded the front door seals to eliminate even more road and wind intrusion. Has anyone on the earlier years swapped these seals out for the newer ones? Where do we find them (with the assurance that they...

My VANOS seals are really leaking.. The whole front of the engine is covered in grime! The passenger side is easy, just remove air intake but the drivers side requires the upper coolant hose to be removed. Has anyone carried out this procedure without disconnecting upper coolant hose? I...

I am replacing my swivel ball oil seals. from what I can see the easiest way to do this is to disconnect the steering bars and remove the whole hub assembly complete from the axle housing. is this correct?