Search Results for ‘seal’

Going through old threads (and calling Rimmer, Rovers North, Famous Four, etc.) it does not appear anyone sells aftermarket window seals. Has anyone come up with a solution to stop water pouring in through the gap between the window and the outer seal? Imagining that maybe I can fit some...

Hi i'm new to these forums so forgive me if i sound a bit newish. my RR sport which i have had from new 2014 been regularly serviced by main dealer and one specialist is leaking from the rear diff. i'm told that its a common problem due to the rear diff pinion seal. i've also been told that JLR...

Replaced rear T-case output seal, want to replace nuts and such on reassemble. The seal was easy to find, but most sellers just have that listed, and not all these other things I need. Any help with part numbers would be muchly appreciated. Also, can the spline seal cause much of a leak? So much...

As per the title, anyone in the Aldershot area with any advice on fixing said leak? I have the seal, Rave suggests a special tool for the job. Is there a way around before I attempt to tear in to it? All advice appreciated. Thanks, Rob.

2006 RR HSE Does anyone know the correct part number for the valve body seal? I have my mechatronic unit out and want to go ahead and replace the seal but I'm finding different ones and I don't want to order the wrong one.

I have a punctured rubber boot at the wheel on the rear axle on my AJV8 2006 that needs to be replaced. It looks like if i take the axle out I need special tools to replace oil seals and axle at the diff and that means I am forced to take it to the dealer ...... Has anyone removed and replaced...

Hello, looking for some help with my issue. So I picked up a 2004 gasoline powered L322 RR for a great deal. She's a real beauty, however she has slipping transmission when hot and P0732 code. Shifts through the gears just fine when cold but pretty quickly when it gets warm it will slip in...

hello all, im wondering if anyone knows if my 2012 L322 SC had a rear window lower seal or scraper in addition to the two side seals, or is it just siliconed on? I think my glass was taken off at one point and I'm wondering if that seal was just never put back on, or as I've been noticing many...

I’d like to keep using my sunroof and avoid the “fix” of just sealing it off. Does anyone have a good resource for a replacement seal hat will keep he water out? During my rebuild I set a goal to fix the center console and the cubby-hole. The lid is in good shape and even the box is as...

hello all, my 2k p38 is developing a drifting brake pedal, it has happened a few times while stopped where the brake sinks slowly and the trucks moves. this causes to either push further or pump the pedal to regain "pressure". thus in my experience it means the seals in the master cylinder are...

Hi everyone, I am the new owner of my first Range Rover HSE. It is a 2011 and i just got it yesterday. I am doing some touch ups to it to get it where I want it like replacing the starter button with a new one, swapping out the lift gate arms, and installing a new roof rail seal as the one on...

I am in the process of removing interior rust and am seeking a fix for a bit of missing quarter window seal. It's about 2 inches along the bottom edge next to the rear door. Silicone it maybe? Or try and source a new seal? So far no luck on the latter.. . Photo attached.

Hi I did have a look to see if there were any threads on here sorry if I over looked it .anyway I have a 93 lwb I'm in need of a new swivel housing kit looking on various web sites the swivel seal comes up with a 8mm 9mm and a 12 mm it has abs any ideas?

95 RR P38 Oil is leaking from the oil filter seal. changed the oil filter, topped off the oil, still squirting out. I suspect this is a stuck pressure relief valve. I don't see it in the ROM. Is it accessible from outside? Any thoughts or recommendations? thanks

I'm in the process of replacing the timing chains, guides, and Vanos seals. I finally got the Jesus bolt off with the right tools and now I need to remove and eventually replace the crank seal in the lower timing cover. My question is, can I use a generic seal tool kit or must I buy the tools...

I have a pretty nasty oil leak accumulating on the subframe that is below where the engine and transmission meet. After thoroughly cleaning the undercarriage, I drove a few miles, parked the truck, and waited a few hours. I just went under it and I can see that there is fluid coming from a...