I am finally getting back into a RRS after I sold my '16 RRS HSE Td6 about a year ago 🙌 My new one is a 2019.
This new one comes with a front license plate, which is not required in AZ. Does anybody know if they drill the holes for them?
I've seen some threads/comments on here saying that...
Can anyone give me any direction on how to change the rear spoiler on my 3.0 2015 sport please.
I have put a new SVR kit on and now need to change the spoiler to the one supplied.
3.0 Sport 2015
I need some advice. I have a 2012 Range Rover HSE i need to know what is easier in pulling the engine out should i pull it from the top or drop it down from the bottom? Any advice is welcome. Thank You.`8)
I'm new to this forum but I'm glad I found it. I'm just wondering- has anyone been able to remove the click and hook? We've had our Range Rover for almost a year now and it seems impossible to remove the accessory.
My running boards came with the truck, and one has take a bit of a beating. Was wondering if it's pretty strait forward to remove them? And also, if I need any other pieces to replace and trim or parts that may have been modified or taken off when they were originally installed.
I cant find out how to remove this radio as I cannot get anything to slide in and around.
It may be the kind you pry off the faceplate but I dont want to break it as I will be selling on fleabay soon.
Here is the pic.
I am trying to replace a burned out headlamp bulb, but I can't figure out how to remove the headlight assembly. I saw a thread with instructions, but the external download link was no longer available. Does anyone have the instructions for this?
i have evoque 2012 pure model . the radio has stopped working and i took it into landrover ,who told me the amp is not working and a fuse has gone , after charging me £180 for this info , told me it would cost a further £1150 to fix it , i declined and have purchased an amp, the same...
Hi guys. New member, first post. I have a 2005 HSE which I purchased about two months ago. It has a few problems and I feel some of them I could cure myself, but need help with the major one at the moment. Yesterday I took out the 6CD changer. Took quite a while as some of you know there are a...
So I've had plenty of cars with and without the cartridge style filter. I had a chance to change out the oil filter today and noticed I can't seem to pull it out of its housing. Is there a special trick to removing the cartridge on a TD6? Thanks!
hello, I'm trying to remove the front panel from the door but it doesn't unhook on the speaker side. Is there an additional screw in that area? Should the speaker be removed first? Does anyone have any step-by-step guidance on how to remove the panel? thank you very much.
This applies to my M62 V8 engined L322 (2003). I'm pretty sure the shroud is different on the Jag powered Landies.
As many of you with the M62 engine know, in order to access nearly everything under the engine bay (accessory belts, water pump, alternator, etc), the entire fan shroud and fan...
I need to remove the rear floor panel as the fuel line from the pump to the filter has corroded and is leaking. Is the panel riveted or spot welded?
i am away at the moment so that’s why I can’t check on the vehicle
thanks for any replies
Wanted to replace my cabin filters as they have done the usual turn to dust - removed two screws but need some help on getting the plastic castings out. They are stiff and
I know there are clips but want to be careful of cracking them. Any thoughts tips or photos of them removed to guide my hand?
I recently installed a rebuilt torque converter in a friend's 2004 RR HSE with BMW transmission. Im a full time mechanic but I've dealt with 2 RR's in my career. Transmission removal, torque converter swap, and transmission replacement went fine. No issues at all. Went to start it and battery...
I’m going to tint wrap my fog lights tomorrow bc they are cloudy, and I never use them. Just want to remove the top bezel, add the vinyl tint, trim to size, and replace bezel. Have searched instructions and tutorials but none are the same as mine. Have tried pulling from the front and pushing...