Range Rovers Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-19 of 138 Results
  1. Range Rover Mark II / P38
    When rebuilding the valve block, I am unclear as to which way these go (as in pic). This pic shown 2 one way and the other in the opposite direction. Any ideas as to whats the correct way? (btw not my pic) Thank in advance
  2. Range Rover Mark III / L322
    Has anyone rebuilt the intake cam sprocket gears? New ones are expensive and with the right alignment and O-ring it will be like new but what size and where to purchase? (I'm on 180K, 2008 HSE 4.4L Jaguar engine) Thanks guy!
  3. Range Rover Sport / L320
    i did some googling but really didn't come up with too much so i figured i would ask here, is there any kind of rebuild kit for the AMK compressors? I rebuilt the hitachi on my LR3 but now it seems the AMK on my RRS is on its way out. If not rebuild-able do people have any luck with some of...
  4. Range Rover Mark II / P38
    Hi All, I'm looking for additional suggestions as I continue to troubleshoot 1999 RR 4.0L GEMs - Blew a head gasket on the passenger side (edge of block at cyl5). After completing the rebuild the engine struggles to start, has a rough idle, stalls if you give it gas and let off the throttle...
  5. Range Rover Classic
    Hey everyone! Long time lurker and first time post… well 2nd because I’m reposting this again because the 1st one didn’t post. Anyways, I have a 1995 Range Rover Classic with a 3.9 engine that I just did a complete topend on it. Replaced the camshaft with a Crower 50299, Crane cams lifters...
  6. Range Rover Classic
    Hey everyone! Long time lurker, possibly 2nd post, but i know i've come to the right place, since i've fixed a lot of issues using this forum. That being said let's jump right into things... I did a complete top end rebuild along with a Crower 50229 cam. replaced timing chain, cam bearings...
  7. Range Rover Classic
    Hi all, The steering on my '91 RRC has had a ton of play in the steering wheel, not really picking up much until about 10° of tilt. It's not surprising given that the truck is 28 years old, but it's been problematic with freeway driving. Over the weekend I had an assistant turn the wheel while...
  8. Atlantic British
    This Weekend Get FREE SHIPPING On EBC Brake Rebuild Kits With Atlantic British!
  9. Range Rover Classic
    Hi all, 1991 Range Rover with 173,000 miles. I posted awhile back about how it wouldn't pass smog, and cylinder #1 had low compression. (Original link down below) Tore the engine down and found that the left head gasket had completely blown out, and decided to overhaul the top end. Over the...
  10. Atlantic British
    Today And Tomorrow Save On Brake Rebuild Kits With Atlantic British!
  11. Range Rover Classic
    I've discovered that, in addition to not having fuel pressure, I also have no spark after reassembling my engine. Nice. I checked the ignition fuse and it's fine. I also removed the HT lead from the distributor and held it 6mm from engine block so see if I had a spark (I didn't). Seeing that I...
  12. Range Rover Mark III / L322
    Hello all, have the redhead of the bunch a 2006 rr sc(still love the beast). Having a intermittent starting problem and have pulled the starter(fun, great time to change my front airbags too). Anybody know if there is a starter rebuild kit, specifically the solenoid contacts as they are worn. I...
  13. Range Rover Classic
    I just got my engine back together after a partial rebuild (rings, bearings, gaskets). I've connected a fuel pressure gauge to the shrader valve on the fuel rail and I have no pressure when I turn the key or try and start it. Where should I start my trouble-shooting?
  14. Range Rover Classic
    I'm replacing the viscous coupling in my 1995 RRC. I'm putting a new bearing and new seal in the VC housing. Do I need to grease the bearing before putting it in the housing, or does it just get lube from the ATF that goes into the transfer case? Thanks, Doug
  15. Range Rover Classic
    Ok so for those that remember, I recovered a low mileage 1983 original Texas import Range Rover (3.5 Carb). It has not run since 1997 when the PO removed one head and it had been sitting since (mostly in a closed garage). PO bought plenty of spare parts and I bought the lot for cheap from the...
  16. Range Rover Mark II / P38
    Need to rebuild my p38 motor. Slipped liner, overheating, rock solid hoses, bla bla bla etc. Looking for recommended sources. Who would you recommend? I'm in Dallas but I'm more interested in quality first and reasonable price. Thanks.
  17. Range Rover Classic
    So when resurrected my 3.5 Carb V8 engine in my barn find 1983 RRC I changed a whole bunch of things and it ran great until now. 500 miles later I started to notice a misfire when cold. Week later and the misfire is noticeable when warm. Engine runs fine otherwise with good oil pressure, no...
  18. Range Rover Classic
    So it’s finally happened. Pull away from the stop sign, and everything feels ok. Get to about 25mph, and the rpm go up but the speed goes down and feels like I’m coasting. I pull over to the side and hear a strange grinding sound even with the transmission put in park. Shut the car off, give it...
  19. Range Rover Mark III / L322
    I have a 2006 HSE. I had the transmission rebuilt last year, a week after the rebuild, the transmission light came on and the truck went into a limp mode. I took the truck back to the shop that did the transmission, he said it was an electrical problem. I took the truck to the dealership and...
1-19 of 138 Results