RangeRovers.net Forum banner

pulley

  1. Supercharged pully size.

    Range Rover Mark III / L322
    Hey everyone! I’m new to the chat. I recently purchased a 2008 Land Rover Range Rover supercharged 4.2L. I have a buddy who makes pulleys. I’m going to have him make some new pulleys out of aluminum so I can swap when I get the new belt. I’m planning on upgrading the supercharged pulley to a...
  2. AJ133 5 litre crank pulley

    Range Rover Mark III / L322
    Hi All, Would anyone know the dimensions of the crank pulley with the spacing for the bolt holes used to attach the puller. I need to look at making a pulley holder and make a puller to remove the pulley for doing chain and tensioner replacements. Or if anyone has access to a tech drawing of...
  3. Weights on crankshaft/damper pulley 2002 P38 4.6

    Range Rover Mark II / P38
    I am in the process of replacing my crank pulley due to it wobbling at idle/low rpm due to rubber deterioration. On removal, I noticed that there is a balance weight attatched to the front inside part of the assembly. A friend provided me with two other pulleys, (both from 4.6 Bosch donors)...
  4. Crankshaft Pulley Installation

    Range Rover Classic
    Getting ready to put my pulley back on and wondering how I'm going to torque it to 160lbs (or whatever the high number is). How do I hold the pulley / flywheel still while cranking the bolt? Lets here those magic tips!
  5. What’s this thing behind the crank pulley?

    Range Rover Mark II / P38
    I picked up a 2002 4.6 last week that I just got running, and there’s this piece behind the crank pulley that spins, wobbles, and makes a little noise. It doesn’t seem to be attached to anything, I can jiggle it around with a screw driver when the truck isn’t running. What is it? I have to do...
  6. Crankshaft pulley not coming off [Solved]

    Range Rover Mark II / P38
    Just looking for a bit of advice - have got the locking nut off of the front of the crankshaft pulley, ready to change the front oil seal, but the pulley doesn't want to follow the nut off. Seems nicely seized on there. Gave it a blast with penetrating lube, but nothing. Anyone any advice on...
  7. AC pulley / clutch stuck or compressor failure

    Range Rover Mark II / P38
    Hi, When we bought our Range Rover the previous owner told us the AC compressor failed. We ordered a used compressor so for preparations, this weekend I had a look at the compressor I noticed the following: I can turn around the outside part (clutch plate?) by hand, but I'm unable to turn the...
  8. VelocityAP ECU Tuning for Range Rover Sport

    Range Rover Sport II / L494
    Hello All, We have just joined the forum as sponsors and look forward to building a great reputation here for our products & customer service. VelocityAP has been around since 2007, gaining a foothold in the Aston Martin world (we are an OEM supplier to Aston Martin Racing) and branching...
  9. WOW, can't believe it was still running - idler pulley

    Range Rover Mark II / P38
    had a loud screech from engine. Car was running just fine. Luckily I was home when I discovered it. The idler completely melted but the tensioner was still applying tension and there was zero damage to the serpentine belt. $20 autozone pulley, 5 minute fix Here it is fixed :
  10. Crankshaft pulley nut size

    Range Rover Classic
    I'm finishing up my head gasket job on my 92 RRC and I'm trying to set the timing. Obviously RAVE has failed me, so does anyone know what size the crankshaft pulley nut is? I'm attempting to turn the engine to TDC on the compression stroke, but can't find a wrench or socket that fits. Any help...
  11. Crankshaft pulley and seal tools

    Range Rover Sport / L320
    Hi All, I have 2006 RRS S/C 4.2 I want to replace the crankshaft fount seal, I see the service manual list a whole bunch of special tools, to remove and install the crankshaft pulley and seal I have listed them at the bottom. Im wondering if anyone has had any luck using generic tools from...
  12. Screaming pulley

    Range Rover Mark III / L322
    I just changed the alternator but all of a sudden there is an unbearable squeek from the front of the engine pulleys. Question is which one that is. Can be the tensioner, the new waterpump which would be weird, the alternator or the crackshaft pulley or the one below that which I do not...
  13. Water Drip from Behind Tensioner/Idle Pulley

    Range Rover Classic
    I have a small water drip that appears to be coming from the back of the tensioner arm. Does this get bolted through to an area that has coolant running through it? I see it appears to have a gasket between the block and arm assembly, so I assume that is the case. Doing a quick search now, I...
  14. Crankshaft Pulley Bolt removal

    Range Rover Classic
    I searched for the best way to remove the bolt that holds the crankshaft pulley in place and two solutions were offered: the "agricultural method" and using an air impact wrench. I didn't have enough room without removing the radiator for the air impact wrench and I thought the crank would just...
  15. Fixed guide pulley

    Range Rover Mark III / L322
    Hello out there. Hope everyone is having a great day/evening. I have a question about the fixed guide pulley on a 2008 Full Size Rover Supercharged. I had developed a squeak from somewhere up into the front on a trip back from California and stopped in Utah to have it fixed. They said they put a...
  16. Exhaust sound change with ECU Tune and Pulley upgrade?

    Range Rover Sport II / L494
    So far a lot of the talk has been that one of the reasons the SVR sounds so good is the engine was remapped to dump a little extra fuel in when you let off the gas to create the popping and backfiring. So my question is, for those that have upgraded their ECU's/Pulley, did the exhaust sound...
  17. Pulley noise from drivers side engine compartment.

    Range Rover Sport / L320
    I have a noise that starts once the car warms up. It's on the drivers side and sounds like a pulley going out. What's on that side that could be going bad? No video at the moment, raining so I can't dig into it right now. Thanks!
  18. ECU Tune and Pulley in Chicago Area

    Range Rover Sport II / L494
    Got a 2016 RRS HSE in Corris Grey with Ebony interior last month. Ordered a Quicksilver exhaust which should be here this week. In the shop getting a gloss black roof wrap, powder coated rims and stealth pack on all other silver/chrome items. Looking to possibly get a tune and a new pulley...
  19. Possible to separate Air-con pulley from compressor?

    Range Rover Mark II / P38
    Hi from Nottinghamshire, UK. I am now in possession of my 2000 P38 with THOR 4.6ltr engine. INCREDIBLE noise emanating from the Air-con compressor, accompanied by grease from deceased pulley bearing. I have ordered a complete 2nd-hand Air-con compressor, but am hoping to salvage the pulley and...
  20. Dealer Price on Water Pump Pulley

    Range Rover Mark III / L322
    I was replacing my coolant hoses, belts, putting in a lower temp t-stat, lubing pulleys, etc, this week. My fan has never been off, and it was super stuck. I accidentally cracked my water pump pulley trying to get it off. I went to the BMW dealer for parts, where I get my 10% BMWCCA discount...
Top