pull

Here's the deal. My wife's lease is up in about 4 months, and we are starting to look at used SUV's to replace it. As of now we have look at XC90's, MB GLS's, Q7's and possibly 2018 Expeditions in the upcoming weeks. I have always been in love with Range Rovers, whether the L405's or the...

My 2001 4.6 P38 has low oil pressure and a knock at hot idle; I'm trying to determine what to do next. I just put it back together after replacing the timing chain, oil pump, and rod bearings. The rods didn't look bad at all and the oil pump wasn't cracked like some people have experienced. I...

I'm having the hardest time finding where to buy (or even a part number) the silver door pull surrounds. Any thoughts?

Hey Everyone - had a question, see if maybe anyone has seen this before or can help me get to where I should look. 1995 LWB, when on highway or above 30mph, car pulls to left when braking. The truck has new pads/discs all around, still tons of life on it. It has upgraded Stainless steel brake...

So after months of research Im ready to pull trigger on a 2015 HSE with Driver assistance, Adaptive Cruise control and Front Climate. Has 37K miles and 2 more years under warranty. For around 57K. Is this a good deal ???. KBB trade in shows around 53K. MSRP was $77500.. I needed mostly safety...

One of the blades broke on my 95 classic. The fan from a 98 P38 fits with a little shaving of the inside of the lower shroud. P38 fan has more pitch but fewer blades. Does it draw more air? My alternative is the one piece fan/clutch from a disco II. Both are at my local U-Pull It.

Hi all me again My wife's l322 is all level with the air suspension but has the inactive air suspension message and all lights off on the air level center console. Purchases the compressor seal kit to replace. And contemplating the icarsoft i910 even though the guts of this l322 are bmw. Anyone...

Anyone got any tips on removing the crankshaft pulley nut, without the special tool ? I take its its a the normal thread (rotate counter clockwise to loosen) on a 2006 range rover sport SC

Anyone here pull and replace their engine? How long did it take? Any tips? Any write ups?

Cops in UK told to pull over ALL Range Rovers because of "keyless theft rash" Pull over ALL Range Rovers in Kensington, police are told in 'keyless' theft crackdown Police in a London borough are being instructed to stop all drivers of Range Rovers to check they own the vehicle because of...

Will a standard OBDII scan tool pull the codes for the suspension light? I have a Gen-Tech OBDII Scan Tool, Model 60694 and was wondering how to pull the code as my sons 2006 Range Rover Sport SC, with 113K miles, has that dreaded suspension light on. I tried pulling OBD codes, with the...

Hi all probably a question thats been asked somewhere before, but being a newbie I need to ask it. My 2.5 dse will not pull away in drive but if I put it in 1 or 2 it's fine then switch to drive & all is well until I stop. I then repeat the process of 1 or 2 then drive? Any IDEAS ON WHAT THE...

Hi, I'm about to pull the front differential third member from my '01. One part of the job I'm unsure of is how much of the front brakes have to be dissassembled in order to separate the front hubs to pull the axle shafts out far enough to remove the diff. The manual makes it sound like...

Using a vacuum brake bleeder to pull new fluid through for Bleed process Im planning on replacing my fluid to see if the 3 amigos problem goes away before I swap out pumps and accumulators, etc. My question is: has anyone used the bleeder from Atlantic british that hooks up to an air...

After quitting my job, I realized what the monthly payments would end up costing me :(. So I thought I'd have to put my Rover on hold. 'Til I found this baby, it's not perfect, a terrible radio install, sagging headliner, cracked windshield, and 206k, but it's my first (sort of) car. It's got a...

Occasionally drops out of DRIVE when stopping can pull on back on shifter and works Sorry for the terrible title. I have an 06 Supercharged with 70k on it. The truck drives/shifts just fine (I do have a funny hum sometimes at low rpm but dont think its related) but occasionally it will slip...