Range Rovers Forum banner
pin
1-14 of 45 Results
  1. Range Rover Mark II / P38
    Does anyone know the part number of this pin that holds the dog guard to the ceiling mount?
  2. Range Rover Sport / L320
    Hey all, New here to RangeRovers.net but excited to join. Found another secret menu on my 2011 RRS (image attached) and looking to see if anyone has any ideas on the PIN. Tried the "753" that works on the diagnostic menu and also "1791" and "663" but none of those work to open it up. Just...
  3. Range Rover Mark II / P38
    I have searched and have not found much info, does anyone have the pin out for the ignition coils?. basically I am retrofitting my older rangie to DIS and I am planning on using p38/d2 rover coils. I have the coils and pigtails, now I need to find wire color and function I/E ground, signal etc...
  4. Range Rover Mark III / L322
    Hello, Have the dreaded fuse 18 problem. luckily my wheel is unlocked. I read through some posts where people mention removing a pin from the ignition tumbler so that you can just turn the key no matter what. I removed the tumbler today but cannot seem to figure out what is being referred to...
  5. Range Rover Classic
    So I'm slowly catching up on the maintenance of my RRC that I've had for over one year. A few weeks ago I re-did the swivel housing gaskets & wheel bearings/set preload on the driver's side. It's an ABS model, and the top swivel pin had just the one large thrust washer, instead of a...
  6. Range Rover Classic
    So I bought a distributor (dizzy) from Jegs for my 95 RRC. all is great with the exception of I received a 2 pin as opposed to a three pin module. Not a biggie, but I can not confirm one thing. Which pin is the + and which is the - on the module. I was able to determine what the three pin...
  7. Range Rover Mark III / L322
    Can someone please let me know where I can find the pin out diagram for the body control module. I've searched the site and can't seem to find it anywhere. Thanks
  8. Range Rover Mark III / L322
    Hi, I need to lock the flywheel of my 2004 Range Rover (BMW M62 engine). The Cam tool locking kit I ordered came with the locking pin (see attached). Its way too long to fit into the Flywheel pin hole. Can someone advise me if this will fit if I cut the length down and if so, what should the...
  9. Range Rover Mark II / P38
    *****Just found answer thanks to "Similar Threads" in box below***** Am I just being dumb? 8-0= I am being asked to input the car's Radio PIN number, but how do I input digits 7, 8, 9, and 0?? Instructions I have read say to use the preset buttons, but I only have 1-6. REALLY hope I'm NOT...
  10. Range Rover Mark II / P38
    Hi all, I've just replaced the front prop shaft after the old one broke free, dented the sump, smashed the gearbox oil pick up pipe and the gear selector switch. Replacement parts were ordered and all was going well until I tried to get the new switch fitted. It seems like the pin that comes...
  11. Range Rover Mark II / P38
    Hi, curious if anyone can provide the pin outs for the abs modulator? They don't seem to be in my version of rave, and I've had no luck in searching. I'm looking for the 99 to 02 with 4 wheel tc. I have the outs for the ecu. Just need them for the brick. Thanks in advance for any help
  12. Range Rover Mark II / P38
    HI sorry for the very random question, i've searched everywhere but have gotten no answers so far so I guess a new post in order. Yesterday I was changing the brakes on the 99 Range Rover and I noticed that all of my carrier pins have a good amount of wobble (up and down,side to side) when there...
  13. Range Rover Mark III / L322
    Hopefully straight forward question, Range rover 2002 L322 petrol V8. Just looking at Rave wiring diagrams showing Multi Function Display plus in the description it does not show or mention a black wire. My car has a black wire in pin 12 of the power plug and also a black wire in the video...
  14. Range Rover Mark II / P38
    Is there some sort of adaptor available, to replace the existing swan neck, with a 'plug in' end, and a vertical plate, to which my combined ball and pin hitch could be bolted, or is it necessary to install a completely new towing bracket? Chris
1-14 of 45 Results
Top