RangeRovers.net Forum banner

outer

  1. Outer door trim clips RRS 2005

    Range Rover Sport / L320
    Hi out there in the woods! I've peeled off the outer trim of the passenger front door to replace some loose/broken clips. Can anyone tell me where the any yellow and the few black clips have to be mounted? All of the old clips were yellow but on the drivers side (2 years ago) not... ... But...
  2. outer cooling fan

    Range Rover Mark III / L322
    Hi all, There are two fans: an outer one ( before the radiator and one behind the radiator ( between radiator and engine block). When I start the engine only the inner one ( which is larger ) starts turning. Questions: -Is that normal ? -How can I check whether the smaller, outer fan ins...
  3. 1995 RRC - Lh outer door handle

    Range Rover Classic
    Broke the door pull on my classic now trying to source a driver side pull seems impossible. I even looked for a rear pull so I could try to swap it out with the front. Anybody know where I can get one?
  4. re-glue the outer door seal?

    Range Rover Sport / L320
    I just noticed my outer door seal is peeling away from the inside door frame near the roof. Everywhere but the roof it looks good. I would guess it's due to years of washing the truck. Has anyone tried to re-glue it or do I peal it and put new double sided tape on it?
  5. Replacing inner and outer tie rod ends advice

    Range Rover Mark III / L322
    I've replaced my right front outer before, and it was pretty easy, but on the left side I have to replace the inner tie rod end also. Never done it before, and am looking for some advice and any helpful hints to make it go easier. Looks like the wide end of the rubber boot is not easily...
  6. P38 Rear Outer light removal advice needed!

    Range Rover Mark II / P38
    Hi I am new to this forum and after looking online and on here I can't find the answer I am looking for so apologies if this has already been covered before. Can anyone tell me how to remove the rear outer light unit on a P38 (2001) Range Rover please?
  7. Windshield Lower Cowl PANEL OUTER FINISHER on 2006 Rover Supercharged Removal How to

    Range Rover Mark III / L322
    Windshield Lower Cowl PANEL OUTER FINISHER on 2006 Rover Supercharged Removal How to I need some help. Anyone have photos or a link to show me how to remove the windshield cowl panel? Or just tell me how to do it? I got to the part where I must (or so I think I do) remove those two...
  8. classic outer door handles and locks

    Range Rover Classic
    I know the door locks have GM stamped on them, and that other BL cars used the same door handles (marina)... watched Police Academy 1 this morning, and just noticed that the squad cars (AMC Matadors) have the same style of door handles... Are they the same? does anyone know? Merry Christmas all!
  9. Range Rover Classic outer window scraper seals

    Range Rover Classic
    Hello all, I am trying to locate the outer window scraper seal that sits inside the main rubber seal. Is anybody still selling these?
  10. Inner and outer tie rod replacement

    Range Rover Mark III / L322
    I'm going to be replacing my tie rods... Inner: MOOG LR-AX-4212 is the same as the genuine land rover part at a fraction of the price. Outer: MOOG LR-ES-3528 also equivalent to the genuine land rover part but much cheaper. I'll update this thread later with more details about how the repair...
  11. side/wing mirror outer cover

    Range Rover Mark III / L322
    I am experiencing a problem with my side wing mirrors where when I press the fold button, they fold in, but then unfold again immediately. I have seen discussions where people discuss checking the micro/limit switch, but I don't know how to remove the outer cover to get to the micro/limit...
  12. Front Brake Caliper (Outer Dust Seal) - How to re-install ??

    Range Rover Mark III / L322
    Hi, I am at a loss to understand how the outer dust seal goes back onto the caliper. There doesn't seem to be enough gap between the brake piston and the caliper. Every time I get it started it just pops out, and forcing it in with a small flat screwdriver doesn't seem the correct way to me...
Top