RangeRovers.net Forum banner

oring

  1. Power Steering o-ring

    Range Rover Sport / L320
    Hey guys, I just installed a new A/C compressor in my 2008 Range Rover Sport HSE and currently putting everything back together. So according to the manual the power steering pump high pressure line has an o-ring, but I can't seem to find mine. My friend who was helping and took that part off...
  2. Bosh Injector o-ring install tools

    Range Rover Mark III / L322
    I was watching the Atlantic British video below regarding removing and installing injectors for a 5.0. I have the tool that removes and installs the injectors. About half way through the video the Tech uses two small tools that install the bottom seal ring and then sizes it. Does anyone know...
  3. Intake Manifold O-ring and Clip

    Range Rover Sport / L320
    Long time reader, first time poster 2006 Range Rover Sport Supercharge with 96000+ miles on the truck. I've been getting P0171 and P0174 codes once in a while and then they would just go away on their own. But few days ago I got bunch of misfires and Reduction of Engine Power messages so I...
  4. Need X8R Oring kit PLUS STC1803 for EAS rebuild?

    Range Rover Mark II / P38
    Do I need both of these kits to rebuild my EAS block in 2000 P38? Or does the X8R kit contain the everything but the bolts? There is some language in the sticky notes about need Atlantic British's kit STC 1803 but not sure if those same orings are already included in the full X8R kit. hard to...
  5. Air reservoir tank connection and o-ring

    Range Rover Mark III / L322
    Hello all. Since the arrival of cold weather, I've developed a slight leak at the rear connection of the air tank reservoir under the car. If the truck sits for a couple of days, the air leaks out of the tank and upon start-up the compressor turns on to fill it up again, which takes 4-5 minutes...
  6. Has anyone used this valve block oring kit?

    Range Rover Mark II / P38
    http://www.ebay.com/ulk/itm/151581747963 I think I need to do mine. Sent from AutoGuide.com Free App
  7. Oil Pressure Bypass Valve O-Ring Replacment

    Range Rover Mark II / P38
    Greetings, Had a chance to replace a leaking oil pressure bypass valve o-ring on my GEMS 96 this afternoon. It was pretty straight forward. The only thing that I wished to have was a long reach pair of circlip pliers. It's a little tight in there with the hoses etc. Gain access by removing...
  8. HELP identifying correct Throttle Body O-ring part # on 2004

    Range Rover Mark III / L322
    2004 petrol USA vehicle. On the throttle body pictured below, my flat gasket has gone to hell as shown where I drew the BLUE circle; it's flat, and has a groove to mate into the Throttle body, and it seals off to the plastic air tube going over to the MAF. Can anyone help me identify the...
  9. O-ring sizes for eas valve block

    Range Rover Mark II / P38
    I recently refurbished the EAS valve block on my 1995 P38 Range Rover with an o-ring kit purchased on eBay from the UK. Touch wood, my Rangie’s air suspension has now been working reliably for more than six months. Just in case of another failure, I bought a spare valve block and am...
  10. A/C O-ring sizes

    Range Rover Mark II / P38
    Just a quickie. I'm fitting a new condenser and receiver, or will be when they arrive, and need to get new O-rings. Are these a standard "air con" size, one for the hot side, one for cold or are they manufacturer specific? They say replace in RAVE but, probably not surprisingly, give no...
  11. Heater o-ring screw part number

    Range Rover Mark II / P38
    Hi, I'm looking for the screw part number but can't find it on Microcat or on google. May you help me? Thanks Florent
  12. RRC EAS O-Ring sizes

    Range Rover Classic
    I've noticed my parts supplier lists three sizes of EAS o-rings - 4mm, 6mm and 8mm - which brings a few questions... Does anyone have a list of where the different sizes are used? Does anyone have any additional dimensions, or a cross reference to standard o-rings? I figure there has to be...
  13. O-Ring size for 6mm air lines?

    Range Rover Mark II / P38
    Does anyone know the O-Ring size for the 6mm air lines. I bought some 6mm IB 10mm OB 2mm thick ORings and they were too thin. I got a valve block rebuild kit and replaced everything in the valve block. Now I would like to replace ORings in the air bags and air tank.
  14. Oil Filler Neck O-Ring / Gasket

    Range Rover Mark II / P38
    Hello to you all. Does anyone have an idea where I can get the O-Ring/Gasket that goes on the oil filler neck where it sits on the valve cover? I have just found searching the neck with the ring for USD $80.00 or used for USD $25.00 ... Of course for this I will like to get a new...
  15. O-Ring sizes for engine rebuild - Anyone have a list of sizes?

    Range Rover Mark II / P38
    O-Ring sizes for engine rebuild - Anyone have a list of sizes? I'm getting ready to put my rebuilt 4.6 back in the P38 and just have to do final touches. The gasket / oring kit I purchased does not have orings for the sensors and other plug ins. Would any of you have a list of replacement...
  16. Need oil pressure reliefe ORing

    Range Rover Mark II / P38
    locating the o ring for the oil pressure relief valves. Doing my oil pump and pulled the front cover off to find these o rings broken and hard as wood, my usual part supplier Atlantic B doesnt carry it. Does anybody have a good source or substitute. 1999 4.0SE Mike
  17. Fuel Pressure Regulator O-ring - US Source

    Range Rover Classic
    Hi there - 1995 RRC, 4.2L. I need to locate a new o-ring for the Fuel Pressure Regulator (ERR6761?) but having trouble locating in the US. The current one is split, and I don't want to have to go buy a new regulator just to get the o-ring. I'm going to try the local NAPA auto parts place to...
  18. Quick valveblock o-ring question

    Range Rover Mark II / P38
    Have been replacing o-rings today, and got quick question. Guide says each air line hole will take two o-rings. However, in the picture, the one with the pink arrow pointing to is (compressor inlet I think?) seems to be a shallower hole. SHould this still take two o-rings?
  19. Heater O-ring project

    Range Rover Mark II / P38
    Hi All, I've been adding coolant now for a few weeks and found that my passenger side (left drive) floor mats were collecting anti-freeze. So armed with some o-rings, I went into the dash using the short cut methods on this site. The first surprise was finding previously cut duct work...
  20. EAS o-ring kit

    Range Rover Mark II / P38
    Hi, Any known place to buy the complete kit, as used to sell by Hardrange of Aus? regds kapila
Top