Range Rovers Forum banner
nut
1-19 of 46 Results
  1. Range Rover Mark II / P38
    Having hard time with the front axle nut. I never have seen this before I’m trying to get a punch screwdriver in to bend back up nothing is working. I couldn’t find anything on site so if there is a post elsewhere I do apologize
  2. Range Rover Mark III / L322
    Are there are direct replacement to the crappy soft lugs nuts for late model L322s? Will the NRC7415 plain steel lug nuts work for 2010-2102 wheels? Any other options?
  3. Range Rover Mark III / L322
    My 2003 RR began making a "clicking" or "knocking" at the left-rear wheel after jacking it up to remove the wheel. Apparently something came loose somewhere, a spline popped out or a retaining ring came off or something. But to get to the problem, I need to remove the "shaft hub nut" from the...
  4. Range Rover Mark III / L322
    Ive been trying to remove my fan to install a new thermostat housing. My question is which way do i need to go to remove the bolt. Ive been tapping and turning with no luck to the left hand side. My vehicle is a 2006 range rover hse 4.4 non sport Model jaguar engine.
  5. Range Rover Mark III / L322
    I have a 2006 Range Rover HSE Full Size and I bought 2005 wheels to put snow tires on. I bought the wheels private party and they did not come with lug nuts. I understand the lug nut design is different for 2003-2005 than 2006+, but I am trying to figure out if the thread size is the same. My...
  6. Range Rover Sport / L320
    Does any body know of a good replacement for the OEM lug nuts that come on a 2008 RRS HSE (19"). My Lugs have an annoying plastic cap that never works with conventional tools. They warp easily and or get stuck in my socket. Either way, it is always some sort of challenge to get my tires off...
  7. Range Rover Mark III / L322
    Model: 2012 RRSC with Variable Damping Hi all, I replaced my right air bag last night. I had previously done the left one which went very smoothly. However this time I'm stumped! So everything went well, I took apart the old one put new bag in, sealed perfectly and assembled. When I...
  8. Range Rover Mark III / L322
    My 04 HSE 4.4 has the wrong sized nut in two places and is spaced out with washers, looking I found the part, but is an outrageous $20. Does anyone know where I can get these for a reasonable price? I do not need the seal, I have a bag of extras from an M62 Non VANOS...
  9. Range Rover Classic
    If you are standing in front of the truck, looking toward the motor, and you put a wrench on the fan nut (36mm?) and are using a tool to stabilize the pulley, which way do you turn the nut to remove? I know this question has been asked before in several of the LR/RR forums and I *thought* I was...
  10. Range Rover Mark II / P38
    A couple of weeks ago, to solve a chi-chi-chi-chi noise that seems to be coming from the front left wheel , mad as suggested I make sure the hub nut is tight. I now have the appropriate 32mm socket. The question is, can I just try to tighten the hub nut as it is, or do I need to remove the stake...
  11. Range Rover Mark III / L322
    I'm looking for black lug nuts for my L322, but don't wanna blow $450 at Land Rover for a new set. Does anyone know a cheaper way? I was thinking about getting a silver set for around $150 and then having them powdercoated? Our TDI Touareg has Lug Nut "caps" that are black but I'm not sure where...
  12. Range Rover Sport / L320
    Anyone got any tips on removing the crankshaft pulley nut, without the special tool ? I take its its a the normal thread (rotate counter clockwise to loosen) on a 2006 range rover sport SC
  13. Range Rover Mark III / L322
    This is one of those threads you read and think "Glad it's not me". I was finishing a timing job on this 4.4 M62 Range Rover HSE. I was reassembling the top and putting on that rail that goes along the cam caps, when I dropped one of those 6mm nuts. It tickled down into the motor somewhere...
  14. Range Rover Classic
    I'm finishing up my head gasket job on my 92 RRC and I'm trying to set the timing. Obviously RAVE has failed me, so does anyone know what size the crankshaft pulley nut is? I'm attempting to turn the engine to TDC on the compression stroke, but can't find a wrench or socket that fits. Any help...
  15. Range Rover Classic
    I've been having problems getting my 90 to run well at idle when it is hot. It's run rich and had intermittent poor performance. I've chased all kinds of rabbit holes, and have not come to a real resolution. I finally decided that I needed to get rovergauge working last weekend and did. Well...
  16. Range Rover Sport / L320
    Can someone please confirm for me which way the viscous fan nut comes off ? I bought a water pump wrench that fits the nut and fits in there and I bought a tool that is supposed to hold the belt pulley to remove the viscous fan - of course it doesn't fit right, but it will hold with one bolt...
  17. Range Rover Mark II / P38
    Does any one know what torque value to use for the wheel nuts when fitting steel wheels to a P38? There's nothing listed in Rave, not surprising really. The wheels are designated by the manufacturer as fitting P38 and Discovery 2 and they've told me it's the same torque value as Land Rover...
  18. Range Rover Mark II / P38
    I have just purchased a set of DISCOVERY 18" for my P38. I know the wheels fit without center rings but what about the Lug Nuts, are Disc11 the same as P38. Now if you know someone who would like a set or 22" KHAN's ????? lol
  19. Range Rover Mark III / L322
    Hi All I am trying to replace my water pump on 2004 4.4 v8 vogue as this has gone and also the alternater belt has snapped. I have got a bwm specials tools to remove the fan but i can not get it to move. I have now broken the pulled and still can not reomve the nut. I am trying to undo the nut...
1-19 of 46 Results
Top