housing

Hi, I have a RRS2010 TDV6 3.0 litre. I have noticed that I have engine oil in mycoolant overflow bottle but no water in the oil or overpressure inthe coolant system and since changing my oil filer an oil leak fromthe top of the engine running down the right side. I have rechargedthe filter and...

Howdy. A simple matter here... Might anyone know the part number for the four, roughly 49 mm spring clips that hold the engine air filter housing closed for a 2004 4.4L? Possible numbers might be PZR000010 or 9628A. Or not. I believe the PZR000020 clips are too short. Some previous mechanic...

Hey all, Just had the wonderful experience of finding oil leaking out from the rubber plug on the trans. Confirmed that oil is coming from the transmission side. Guessing its the transmission front seal. Going to pull the trans and replace the seal, but never want to pull the trans again so am...

Hi folks, my first post after having used this source of wisdom for a while. So I am a bit concerned: I started up my engine yesterday (cold start, night time temperature approx 10 degrees Celsius ) and after 10 seconds or so engine oil started to ooze out of the oil filter housing, at the...

Just took my 04 in for an oil change. the dealer pointed out that the last dealer must have broken the little plastic pipe that the oil filter slides over inside the oil filter housing as it is now broken. they can't find a used one and apparently that part is not sold separate from the oil...

Bought the fuel filler door latch kit for my 2008 Range Rover Sport HSE. Found I was unable to use it due to plastic that holds the clip inside the fuel filler housing broken. I can buy a new housing for $80, but looking at it I would have no idea how to get the old one out, new one in, and...

Anyone knows the part number for that black cap or blind plug located in the back of the water cooled alternator housing? This is on the m62tu 4.4 lower timing cover. I searched on parts websites and can’t seem to find it anywhere, not even in diagrams. Took the freshly built rover on on the...

My thermostat housing on my 2006 range rover hse 4.4 cracked while replacing the coolant sensor. Can anyone give me a write up of how to remove it? I have the new one in hand.

I have a 2010 RRS SC. I decided to save some money by changing my own oil. The oil filter cap is stuck. I have tried various filter wrenches/straps, but it won't budge. I know "left = loose, right = tight" and I am a relatively strong individual, so it seems that the dealer over-tightened...

I have 2004 Range and I blew the water pump, fixed that with a re and re turned out great! <br> <br> Then I fired it up before filling with coolant to ensure the belts were nice and inline, 30 seconds.<br> <br> Then I added my coolant and after about 1 jug it began slowing up and I released...

Hi All, I performed an oil change on my 2002 L322 (BMW 4.4L) and there seemed to be a couple of locating 'tabs' missing from inside the oil filter housing cap? Can someone confirm if there are supposed to be 6 tabs that clip into the top of the filter? Mine only has 4... Regards Morgan

its a 2010 tdv8 and the suspension goes up and down fine with no dashboard messages etc. a continuous clicking noise (about 1 per second) can heard which is coming from the black suspension pump housing under the spare wheel. operating the pump to raise suspension makes it stop but shortly...

Hello Fellow Rovers! I am hoping for some guidance from the knowledge bank out there. I see that my RRC is missing the round inspection plate that fits on the bottom of the bell housing. the one with 3 bolt holes. I am going to fabricate the cover, i would like to know 2 things: 1) what...

Working on pulling my 95 RRC 4.2L engine. I have two bolts on the left bell housing that are proving to be a bit of a challenge. these are the ones on the side. I have the tops and bottom ones off. Just wondering if anyone has a trick to getting to these. Will it help to remove the engine...

First Thank everyone in Advance! I am changing my front differential Today. Have My half axles out wheels , calipers. Front Drive shaft. Yadda Yadda.. But When I was doing a ram rod cleaning on the front axle housing and the differential I noticed 1 Little round metal "spring" Then after...

I've been experiencing a bad rattle from the subwoofer lately. Suspecting it was just a lose bolt, I inspected today to find that the plastic housing is cracked right where the bolt (which is visible from removing the panel that covers the DVD player) is. It has about a 1/4 inch of play up and...

I was trying to reprogram my key fob but the lock button has just totally worn out and doesn't work. I don't need one with a blank key but I just want to transfer the key and transponder guts to a new unit. Has anyone done this? Have an 04 HSE. Sent from my iPhone using Tapatalk

My friend is telling me I need a whole new light is this true? Or is there a part just for the plastic. 2015 range supercharged

I am wondering the stud size for range rover at the point where the header ends. Its a triangle looking gasket with 3 studs. I have seen 5/16-24x 1.5"but would like to verify before ordering. Also can I install and remove the engine with the headers intact or should I remove them? Also does...

Hi, i'm new here so hope i'm posting in the correct place. I've recently purchased a 2004 Range Rover td6 and wish to change the filters. Im starting with the oil filter. Its currently broken so i purchased a new one with the housing because the old one could not be removed. There are 6 screws /...