Search Results for ‘heads’

So I’m doing a head job on my 2007 L322 non superched and I can seem to find the torque specs and tightening order for the cylinder heads and intake can any one help with this information? I would greatly appreciate it.

Hi everyone, I ordered a 2019 RRS HSE V6 dynamic with: blacked out rims, cooled seats, full camera package (new for 2019), tow hitch, plug in back, refrigerator. Is the heads up display worth it? Anything I left out? Thank you!

I'm working on my heads now but I haven't never seen this before. Anybody know if that hump in the exhaust port can be removed? I don't see anything going to it but I can't be 100% sure it won't open up if I remove it

Hi, I am debating getting out of my 2017 Audi Q7 and into a SWB V8 Rover. Is heads up display standard? No dealer can answer intelligently and on the RR configurator, they only have the 2018 models so I can't even figure out which option package has the HUD for a 2017. Thanks in advance for...

Is it common that when you redo your head gaskets that something else in the engine wants attention? Just redid my head gaskets about 200 miles ago. Last night I started hearing this: What is your diagnosis? https://www.dropbox.com/s/4h9palebegnrixq/20171128_012821.mp4?dl=0 and this...

I just got the unfortunate news from my dealer just 2 days after I took delivery that my First Edition cannot have roof load bars installed because Land Rover is restricting dealers from retrofitting roof rails on new Velars that were not originally equipped at the factory with them...

Heads up to all who own 2008 Range Rover HSE or are considering to buy Range Rovers…. I want to share my story regarding a serious slow fuel line leak in the vintage 2008 Range Rover that I bought. The vehicle was very meticulously maintained. However I was shocked to find that the fuel rail...

Hi guys, About 20,000km ago I purchased a 96 4.6 on a bit of a whim. In that time I've grown very fond of the old bus and its now time to give him a little love. It has always had what I presumed to be a lifter noise. A few weeks back it developed a rough idle, which I traced to the left bank...

Range Rover Velar Heads to the US Later This Year With $50,895 Price Tag Read more about the Range Rover Velar Heads to the US Later This Year With $50,895 Price Tag at AutoGuide.com.

Hi Guys, Just wanted to share a quick bit of info. Some of the 2017 RRS are being shiped out without the duct connection from the heater/Cooled air unit within seats climate system. This was the case with 2 vehicles at my local LR dealership- one of them being mine. Order numbers were...

i am putting my engine back in, and i am finding my notes to be incomplete. i remember having to remove some wires both fixed and clamped at the back of the engine, but for the life of me, i can not find any notes on which wires were attached/routed. i found my grounds, and i know they attach...

Hi Does anyone know how well the Heads Up Display works, especially when wearing sunglasses? I have a BMW with it, but when I wear sunglasses it is very hard to see it. Thinking of getting it on my RRS 2016…. thanks for the help

No, I don't think so either. But I'm not sure how to explain what I've observed: Last night, I was driving my 2000 RR SE on the interstate at 65mph when the heat started blowing cold, the temperature gauge pegged hot and I pulled off to the shoulder and shut the engine off. Maybe 15 seconds...

My head gasket has gone on my P38. I have been offered another GOOD engine from a P38 with the Aluminium manifold(mine is plastic). Apart from the mounting bolts on the head to manifold being in a different position(which I can re-Drill) Is there any other difference? It is just much easier and...

http://www.gtspirit.com/2014/09/19/official-2015-range-rover-evoque-sw1/ Looks like the heads-up display is finally arriving, I hope the 2015.5 or 2016 full size will get it too. On the other hand, I wonder what a windshield replacement will cost with this...

Hi guys I’m doing a head gasket replacement on my 4.6 and at the stage when the heads are back from the machine shop and I’m about to refit them. I know I need to clean the block face really well before putting the gasket and heads on, and was going to use fine wet & dry sandpaper. But …...