RangeRovers.net Forum banner

guard

  1. Range Rover Mark II / P38
    Does anyone know the part number of this pin that holds the dog guard to the ceiling mount?
  2. Range Rover Mark III / L322
    My 2006 RRSC is missing some fasteners from the inner wheel well. I'm not sure if these are screws, or some type of trim fasteners that either push or turn. I have searched on this site, and internet trying to figure out what type of fastener I need to buy. I'm also in search of fasteners...
  3. Range Rover Classic
    I just got my refurbished brushguard for my Classic. Does anybody have any input on mounting? I just put a brand new air dam on the truck and want to make sure I cut it right. Any ideas on how to cut the air dam and how to make sure it lines up correctly. Should I remove the air dam, install the...
  4. Range Rover Mark III / L322
    Does anyone have a copy of the installation instructions for the bumper guard they could share? I'm interested to take a look to see if it could be modified to fit my 2011. I know the bumper contours are not the same after the facelift, but I'd like to prove it impossible before I give up on the...
  5. Range Rover Sport / L320
    I have an '09 RRS HSE... I know these are very similar to the LR3/4. I want a "half" brush guard like I have seen on some LR4s. Has anyone tried to mount one to a Sport? Seems like it should be possible: (I'm not sure who's truck this is, but it is awesome). This listing shows the...
  6. Range Rover Mark III / L322
    Hi all, this weekend I was doing some work on my dads L322 and was looking for some info on changing the rear brake mud shield/guard. Because of its ridiculous design you have to remove the hub/assembly and would probably end up changing the wheel bearing at the same time. I noticed Atlantic...
  7. Range Rover Mark IV / L405
    I just ordered my '17 and the only dog / Luggage guard that is offered from JLR is a full cage that goes from floor to ceiling. In my MK3 I have the one that covers only from the top of the seats to the ceiling.... This makes it much easier if i have to lay the seats down and put something long...
  8. Range Rover Classic
    I just had a set of new mounts fabricated for my OEM dog guard (the brackets with the hand dial that mount to the seat latch box). Before I start drilling holes, can someone please post pics of your install? The old install from the PO was crappy. I believe they mount in front of the push...
  9. Range Rover Mark III / L322
    Anyone successfully put a 2003-2005 grill guard on a 06-onward of the MKIII? I was hit by someone who ran a red light and apparently the grill guard is no longer available. Definitely want a grill guard on and am wondering how different the 03-05 one is and if it can be mounted on a later model...
  10. Range Rover Mark III / L322
    Can anyone confirm for certain whether it's possible to install an 03-05 OEM wrap around brush guard on an 06+? Interference with parking sensors is irrelevant - I only care about the mounting points. I've seen conflicting info online. Thanks!
  11. Range Rover Mark III / L322
    Hi, Got a 2006 4.2 SC recently and wanted to install a Mantec sump guard i had. This type Any clue to install it. I can't find any photo of this specific sump guard on a L322. But i have tons of photos of G4 challenge L322 with other sump guards. Thanks Florent
  12. Range Rover Mark III / L322
    Hello, looking for bolt sizes. Does anyone know the bolt size for say the bull bar? The front bar under bumper skin has threaded holes for bull bar etc and it would help me if I could buy bolts befor removing bumper skin. Also, anyone know the roof rack bolt sizes? Thank you
  13. Range Rover Mark III / L322
    Im in the process of purchasing a 2008 Range Rover supercharged hse model, & I want to install a full grill guard. Now I have found no information online if it is possible to find an aftermarket guard. I also want to install fog lights within the grill guard. Does anyone know if it is possible...
  14. Range Rover Classic
    Does anyone know where I can find replacement rubber inserts to a factory brush guard?
  15. Range Rover Classic
    Good morning (to those of us in Central Time)…..recovering from a Jack Daniels evening……… Purpose of this post: I have purchased an aftermarket Brush Guard (BG) from "Rovaguy" in VA, Will Tillery. Got a great deal (this guy is probably the BEST source, IMHO, for Classic parts) and I bought a...
  16. Range Rover Mark III / L322
    I'm planning some offroad trips in the next few months and want to beef up some of my exterior for added protection. Most off road treks will be in rocky terrain. I am not having much luck finding tubular rock sliders or tubular bull bars/ brush guards for my model which is a 2011 HSE (full...
  17. Range Rover Mark II / P38
    Has anyone ever removed the foam from the brush guard and refinished it without the foam? Mine looks very aged and I would like to clean it up. My company does media blasting and powder coating but im not sure if it would look any good with the foam removed
  18. Range Rover Mark III / L322
    Hey all, I was browsing through the forums and I saw somebody posted this website that makes bumper guards for 02-12 Range Rovers: https://tacticalarmorgroup.com/TAG-Bumper-Store/catpageindex/8/CreatedByUser/1/Wincher-Land-Rover-Range-Rover?txtSearch=* I was wondering if anybody has any...
  19. Range Rover Mark III / L322
    I really wanted to try and snap a picture of the front end of my car to help in the description of this post, but I got home from work after the sun set. So I will do my best to describe the part in question even though I don't know the technical name for it. In the morning I'll try and snap a...
  20. Range Rover Mark IV / L405
    is it possible to have them stay out when parking in tight lots and would it be effective door ding protection?
Top