RangeRovers.net Forum banner

chassis

  1. Early 2 door rear chassis crossmember help

    Range Rover Classic
    Hi, this is my first post so hello to you all. Need pics or measurements to construct the repairs to the rear crossmember that holds the fuel tank on my ‘72 2 door, the correct 3 bolt mountings needed etc. Seems no one sells a rear crossmember, have a later chassis but mountings are different...
  2. L322 Vogue DVD Chassis bolts

    Range Rover Mark III / L322
    Does anyone happen to know the size of the bolts that hold the GPS DVD Chassis in the frame in the boot. I’ve managed to drop a couple whilst removing it
  3. Defender 100 on p38 chassis?

    Range Rover Mark II / P38
    Hi, After watching a 4x4 is born for the 4th time i was wondering if it will be possible to do the same with my 4.6 bosch? Has anyone ever done this? The idea is to buy a 3.5 and bolt all the ancillaries onto the 4.6. I wonder if the old carbs will keep up with the 4.6.? Ill also need to find a...
  4. Suggestions to wash the chassis

    Range Rover Mark III / L322
    Any suggestions, comments or tips before clean under a Range Rover 2004? For the purpose of solve an oil leak im going to clean under, but im afraid of damage something like sensors and stuff like that. Best regards.
  5. Where can I find the chassis VIN # ?

    Range Rover Sport II / L494
    I'm looking to buy my first Land Rover. It's a private sale of a 2014 Range Rover Sport SC V8 and I'm just being extra cautious and want to confirm the VIN # on the windshield matches. It's a Canadian vehicle so I think the door sticker will have it but there should be one somewhere else too ?
  6. Chassis swap

    Range Rover Classic
    Hi guys. Hope someone can answer this question. Is it possible to put a 1998 range rover shell on a 1994 chassis ? Many thanks.
  7. 97 4.6: No Engine, need to move chassis, thoughts?

    Range Rover Mark II / P38
    Hey there all! been lurking a while as I get our 97 4.6 back up to snuff, thanks for all of the info you have provided! I'm hitting the stage where the engine is coming out for a serious bit of R&R. At 214k miles, we have to put a full dose of oil in over a 300mile trip. My issue is this. I...
  8. bumpstop mount to chassis

    Range Rover Mark II / P38
    strange question... is the bumpstopmount on the chassis welded or can the dish and the "mushroom" be screwed off?
  9. VIN on chassis?

    Range Rover Mark II / P38
    Hi All, My RR has no sticker with the VIN number. Is the number on the chassis somewhere? (I know it is on a plate behind the winscreen). Where? Cheers.
  10. Range Rover Classic Chassis Number

    Range Rover Classic
    Dear All, i am in the process of buying a 1986 Range Rover and need to know what th chassis number should read with regards to how many digits and characters and if in 1986 the RR was already with the SAL thanks a bunch hello from malta Jake
  11. Chassis replaced for later type now have height issues

    Range Rover Mark II / P38
    Hi, A good friend has replaced his chassis that had the 3 bolt hole height sensors for a later chassis that uses the 2 bolt hole. I got involved to fit the new sensors and re wiring needed to sort the eas out. The problem is that the height is too high on the front, but ok on the back ! I know...
  12. Chassis # Issues

    Range Rover Classic
    Hello Fellow Landy Lovers, I need some help. I recently restored a 1976 2-Door Range Rover classic. After the three month restoration, I shipped it to Florida from our shop over seas. Whilst getting the truck inspected by the local DMV so I could then transfer the title to an American one, the...
  13. 72 Range Rover engine and chassis numbers

    Range Rover Classic
    Range Rover classic
  14. The Search For A Galvanised Chassis

    Range Rover Classic
    Could someone please advise me where to obtain a galvanised chassis for a re-build of my beloved Classic Range Rover, 1994. I've been informed that it is possible to buy a NEW one, but i have been unable to source one. I would be very grateful for any advice. Also I would very much like to buy a...
  15. L322 Chassis issue - should I sell it as a project?

    Range Rover Mark III / L322
    Hi, looking for some advice. I've been well and truly ripped off by a dealer in Nottingham, SON prestige and now don't know what to do. We bought a face lifted 2002 L322 for £11,000 about 8 months ago so I'm not covered by the Sales of Goods act as thats only the first 6 months. It's had...
  16. 93 RR 3.9 Manual KA Chassis no initial flat accelerator on Petrol runs fine on LPG

    Range Rover Classic
    93 RR 3.9 Manual KA Chassis no initial flat accelerator on Petrol runs fine on LPG I have a 93 RRC with the 3.9 EFI V8 it has LPG and is experiencing an inital acceleration problem which is particular to running on petrol. When you go to start off from being stopped in first gear you squeeze...
  17. RRC Chassis conversion

    Range Rover Classic
    Hi guys, I'm looking for some useful advice with regards to a chassis conversion. I am from Ireland, the Republic, and I have been thinking about starting a new project. Long story short, I'd like to install a 94' V8 petrol body onto a 1970's 2 door RRC chassis. I understand that there are just...
  18. Trying to use P38 chassis for off-road fun

    Range Rover Mark II / P38
    I've got a '96 P38 with a 4.0 that doesn't run and I can't drive it. I've looked underneath it and was impressed at how the suspension was set up. I like to do things that are a bit different, so am looking into pulling the body off the frame, and swapping a different body onto it. Probably an...
  19. Side Steps chassis bolts.

    Range Rover Mark II / P38
    Hi all, Just bought myself a pair of secondhand side steps for my 2001 P38 and I can see the holes in the chassis but have no idea what size bolts to use. I've spoken today to the parts dept at a local Land Rover dealership and the fella there says he doesn't have the bolts listed as they came...
  20. Chassis support necessary when depressurizing?

    Range Rover Mark II / P38
    Hello! I have a -98 RR p38 4.6 HSE. I'm about to renovate my valve block and compressor with a renovation kit from symlise on ebay. The EAS is working ok but it is sometimes slow to rise in the mornings when I want to raise it from standard to extended height for example. I find the renovation...
Top