RangeRovers.net Forum banner

camshaft

  1. 2004 vanos/camshaft sensor/solenoid problem

    Range Rover Mark III / L322
    Hi all!! I have recently purchased a 2004 Range Rover. I bought it after sitting for around 4 years. It’s in pretty sad shape, but I am no stranger to projects — and especially not afraid of range rovers/bmw’s. When I first purchased, was told it needed a transmission, but it turned out that it...
  2. M62 4.4 Camshaft Position Sensor

    Range Rover Mark III / L322
    I've bought two CPS (BBR Automotive Germany) to replace the current CPS of my RR. It's an easy job to do at home? Is there a guideon how to proceed? After replacing the sensors there is clean code needed? I found this guide for a BMW 540i E39...
  3. CamShaft Position Sensor "LR014372"

    Range Rover Sport II / L494
    Hi Do-It-Yourself, I need a Picture or Video or a very good description of the Location of the "CamShaft Position Sensor "LR014372" on a 2016 Sport SC. Is the sensor on top or bottom or inside the engine? From the YouTube videos so far, I suspect it is at the bottom, but I'm not sure, because...
  4. Camshaft Position Sensor Codes - Not Starting

    Range Rover Mark III / L322
    Hi My 2005 L322 Supercharged is a non-starter. ECU is showing P0340 and P0345 which indicate an issue with the Camshaft Position Sensor. Some of the reading I've done around this suggest the fix may not be as simple as replacing the faulty sensor(s). Does anyone have any experience of the...
  5. Error P0340 - Camshaft Position Sensor "A" Circuit

    Range Rover Mark II / P38
    Fellow P38'rs, I've already done a bunch of work getting to where I am in this post clearing several previous codes etc... The only major replacement I have done was a new MAF sensor, otherwise all other work has been general maintenance and cleaning. My major problems have been intermittent...
  6. Fel Pro camshaft cover gaskets

    Range Rover Mark III / L322
    I just replaced my camshaft cover gaskets for the 2nd time (1st time at 80k miles, this time at 170k miles), this time with Fel Pro gaskets from Rock Auto. The Fel Pros certainly seemed to fit better, with no problem with the tab at the rear o the heads. Also no sign of a leak afterwards. I also...
  7. camshaft position sensor on 2000 range rover 4.0

    Range Rover Mark II / P38
    Can anyone have any pics or any idea where i must looking for camshaft position sensor on 2000 range rover 4.0 ?
  8. Camshaft Sprocket Bolt.. Way too tight?

    Range Rover Mark III / L322
    I started my VANOS a while ago, but with my hectic schedule I just got to the VANOS itself. Now, tried undoing the exhaust sprocket and couldn't budge it with a 2ft breaker bar and a 3ft PVC "extension." Put some AeroKroil on it but there's not really anywhere for the stuff to work. The actual...
  9. GEMS V8 Camshaft Core Plug

    Range Rover Mark II / P38
    Guys, About to start ordering parts for my V8 rebuild, but wondering about the core plug at the rear of the camshaft. Does this also serve as the rear thrust bearing for the camshaft end float, or should there be some kind of bearing in there ? All the parts books I have looked at only show a...
  10. Maybe the leak is not the Rear Main Seal?!?

    Range Rover Mark III / L322
    I have a pretty nasty oil leak accumulating on the subframe that is below where the engine and transmission meet. After thoroughly cleaning the undercarriage, I drove a few miles, parked the truck, and waited a few hours. I just went under it and I can see that there is fluid coming from a...
  11. Ran into a problem with the intake camshaft...

    Range Rover Mark III / L322
    2003 Range Rover w/ 134k miles. A few weeks ago I got the P0011 code, had a small rattle and knew it was time to park it and do timing chain guides. As I got in there, the U guide had plastic missing and what was there wasn't attached to the metal part of the guide. Good thing I caught this...
  12. Camshaft bearing tool...

    Range Rover Mark II / P38
    ...morning All, Bit of a long shot... Does anyone in the UK have a set of camshaft bearing tools that I could borrow/hire, or even a Lisle 18000, to remove and fit the bearings on a 4.6 V8? I missed out on a set on ebay over the weekend, and that's rather buggered me up. :? Many thanks Tim
  13. Camshaft sensor fault

    Range Rover Mark II / P38
    I have P38 4.6HSE (bosch 7/1999). My camshaft sensor showed error (camshaft sensor fault/valve timing error). I bought a new camshaft sensor and changed it. After starting the fault has disappeared, but after driving 60 km to bug reappeared. Where is the problem? Thank you and I'm sorry for my...
  14. Camshaft replacement - how much disassembly?

    Range Rover Mark II / P38
    I am fairly certain that I know the answer to this question, but do I need to pull the pushrods and lifters to remove/replace the camshaft? This is a 1995 4.0 with 196,000 miles. I have the front cover off to replace the gasket (leaking a lot of oil) only to discover that the timing chain...
  15. Camshaft buying advise please

    Range Rover Mark II / P38
    2000 4.6 Bosch engine, in need of a new cam. Two dilemma's: Original LR or aftermarket at one third of the price (including lifters!). There is a saying 'cheap parts are cheap for a reason' so how important is the part that justifies Original, or, is aftermarket really that bad? Standard or...
  16. New Camshaft break-in with a ZF4 transmission?

    Range Rover Mark II / P38
    I have finally got my rebuilt engine installed and will be starting up today or tomorrow, depending on how much "real work" interferes. Problem is, new cams should be work hardened by running at 2000 rpm for 15-20 minutes. I understand this has the potential of damaging the transmission in these...
  17. Camshaft preload on lifters question.

    Range Rover Mark II / P38
    Qu for those of you who have changed the cam if that is OK? When there is talk of sorting preload on the lifters, (shim under foot of rocker arm) is this to compensate for wear on the rocker arm? From my simple brain I am guessing as you now have extra length so to speak on the push rod thanks...
  18. Camshaft purchase question.

    Range Rover Mark II / P38
    Am looking to purchase replacement camshaft (pack with all associated things such as followers) Can I ask for any input from those who have done this, where did you buy the replacement stuff from and would you rate it. Have to purchase tomorow or Thurs! Many thanks again. Ben.
  19. Random Misfire / Camshaft Control Bank 1 Fault

    Range Rover Mark III / L322
    So yesterday I went out to start my 04 HSE and it started to misfire, Hooked it up to AllComms and got a Misfire 1,3,2 Random misfire. Cleared the codes and swapped the coil packs around thinking I might have a couple bad packs... Started the truck and the same misfire 1,3,2 Random misfire. I...
  20. Camshaft sensor ???

    Range Rover Mark II / P38
    Hi all, Need some advise, Back ground - bought RR running very rough, told camshaft sensor gone (well gone did test and inspect before and after removal), removed old one (black plug) refitted new one. This is the problem still running rough with new sensor throwing P0340 code after more...
Top