RangeRovers.net Forum banner

cam

  1. Range Rover Sport / L320
    Hello. I'm new to this forum and need some help. Can anyone tell me where I can find torque specs for my vehicle? I am finishing the installation of the heads and am particularly looking for cam cap torque specs. I can't seem to find them online. Thanks
  2. Range Rover Classic
    Hey everyone! Long time lurker and first time post… well 2nd because I’m reposting this again because the 1st one didn’t post. Anyways, I have a 1995 Range Rover Classic with a 3.9 engine that I just did a complete topend on it. Replaced the camshaft with a Crower 50299, Crane cams lifters...
  3. Range Rover Classic
    Hey everyone! Long time lurker, possibly 2nd post, but i know i've come to the right place, since i've fixed a lot of issues using this forum. That being said let's jump right into things... I did a complete top end rebuild along with a Crower 50229 cam. replaced timing chain, cam bearings...
  4. Range Rover Mark II / P38
    I’ve been doing some research on where to take the 4.6 and turners offer H180 Sports Torque Kent Camshaft upgrade, is anyone using this set up and would you recommend it ?
  5. Range Rover Mark III / L322
    need help locating bank 1 cam position sensor on my 2006 4.4L ( JAG ) range rover sport Also just double checking its not the VTS ( sensor for adjusting valve timing on front of valve cover ) ? I need a diagram or picture or link that shows location please
  6. Range Rover Mark III / L322
    New to teh forum, so Hello! I have a 2010 Range rover with the 5.0 SC. The tensioner broke on the timing chain and I'm putting a new one in. The problem is when I sent the heads in to be checked and cleaned the machine shop removed the markings identifying the intake and exhaust cam shafts...
  7. Range Rover Mark III / L322
    Hi Has anyone tried welding back the broken tabs on a steering tilt cam? I just bought a welder and I think ill give it a shot.
  8. Range Rover Sport II / L494
    Hi, Came across this website selling Sport specific dash cams that fit flush beneath the rear view mirror mount(Type A in the description). https://www.kammu.com Have contacted them a couple of times, but no answer. Have any of you guys out there tried them?
  9. Range Rover Mark II / P38
    Update on changing the cam timing on1999 P38. Earlier post; anyone ever advancethe cam timing on a 1999 4.6 Bosch engine It has been about 2 years now when Iasked the question and at the time everyone told me it could not bedone without problems. I very pleased with the results. I converted a GM...
  10. Range Rover Mark III / L322
    Couple of questions on my 2010 TDV8 1/ To remove the overhead reading light/sunroof controls panel. is it simply a matter of removing the two small hex-head screws visible when the sun-specs holder is lowered? 2/ I'm looking for an ignition switched 12V supply and earth point to power my...
  11. Range Rover Classic
    Getting ready to put the heads back on and I want to be sure the followers are in good shape. How do you determine if they are still good (aside from obvious physical signs)? I also noticed that the push rod for the #8 cylinder was slightly bent - is this because the follower went bad? Not sure...
  12. Range Rover Classic
    Wondering how to tell if my cam followers need to be replaced. Visually, I'm not seeing any odd wear on the contact surfaces and the cam looks to be in good shape. The engine was replaced in the past so I have no idea how many original miles are on it. Thanks.
  13. Range Rover Mark III / L322
    I am trying to remove the inner torx on the cam shafts. I took the larger 15/16 bolt off without aproblem reverse thread. The video I saw, Nathan’s Garage, has the inner Torx beingreverse thread as well. Try as I might,its not budging and I am reluctant to wrench on it to hard for fear of...
  14. Range Rover Mark IV / L405
    Hi, I am intending to install a 2 ch dash cam in my 2015 RR SC. Instead of an additional power source (like a Cellink Battery B) I am planning to use the second battery (for start/stop) instead. My question - would that be ok or I am missing something what would prevent that? Thanks for your...
  15. Range Rover Evoque / L538
    Engine malfunction light came on-service said just needed software update-that didn't work-then they said cam bolt broke-been in shop almost 2 weeks-timing correlation fault. What's up?
  16. Range Rover Sport II / L494
    Has anyone installed a dash cam? Does it work with the heated windshield without video focus or images issues? Thank you
  17. Range Rover Mark IV / L405
    Hello, I am wondering if anyone has a solution to this... Whenever I put my 2016 LWB L405 into reverse, the reverse cam comes on (as expected). However, when I then put it into drive, the front camera does not come on. I need this to help me park in the garage; the park distance control...
  18. Range Rover Sport / L320
    Thought I would briefly (LOL) describe my experience of fitting both a reversing camera and dash-cam to my 2006 Supercharged RR Sport. It all started ironically when the glass tailgate refused to open and for a period of time I gained access to it by drilling a hole in the bottom panel that...
  19. Range Rover Mark III / L322
    Hello, I am searching for part number YPC901330. This is the L322 2005- plug that connects to the venture cam through the glove box. It is an 8pin 2 row connector that mates with the camera side header. The camera side header is black and labelled Tyco/TE AMP. After weeks of searching Tyco/TE...
  20. Range Rover Mark III / L322
    Two issues. '12 RR Supercharged 50K miles 1. Random yellow restricted performance warning. Turns off after a few minutes. Need to turn off vehicle to regain normal performance. No check engine No red warning. Illuminates maybe 1/5 times with full power acceleration. Dealer found no faults...
Top