Range Rovers Forum banner
bush
1-13 of 15 Results
  1. Range Rover Mark II / P38
    I have had a pleasant day in my new shop building working on the front end of "Bolt" (2002 White) Replaced all of the front end bushings except Pan Hard Rod. Got some nice ones on Ebay. 80 bucks complete and all hardware was British, rubber parts were good looking Indian made. I have been aware...
  2. Range Rover Mark II / P38
    Fitting some new front shocks - here it is pictured as it came in the box. Looking at the RAVE file it looks like I should rotate the metal washer at the top and bottom so the "peak" of the cone is against the rubber. Is that correct please? The diagram is not the clearest and I am not sure why...
  3. Range Rover Mark III / L322
    Hi, unfortunately me 2002 L322 failed it's MOT, while I have been able to do most of the work my home made extraction tool is not up to the L322 rear outer balljoint/bush, I am looking for anyone that is willing to lend, hire or sell me the extraction tool, would prefer if they were within...
  4. Range Rover Mark III / L322
    I'm planning some offroad trips in the next few months and want to beef up some of my exterior for added protection. Most off road treks will be in rocky terrain. I am not having much luck finding tubular rock sliders or tubular bull bars/ brush guards for my model which is a 2011 HSE (full...
  5. Range Rover Sport / L320
    Hi again. Does anybody know If I am able to get a bull/bush bar to fit the RR sport? Even aftermarket! I have looked and cannot find a thing, wondering If I will have to get one made? Hit a Deer last week and don't want to have to replace the bumper again lol. Thx
  6. Range Rover Sport / L320
    I'm trying to figure out why the rrs has 0 choices for bumpers. Any ideas?
  7. Range Rover Sport / L320
    Hi everyone, First of all, I present myself, I am french and I just buy a RRS TDV8 year of 2009. (and sorry for my english :D ) Thank you to all for all threads I have find into this Nice Forum. So, I have a vibration when I drive at 80km/h (only when I decelerate), I have look under the...
  8. Range Rover Mark II / P38
    After thwacking the expensive heated windscreen last weekend whilst off roading in some forestry (and luckily getting away with it) I have bought a set of bush cables - as they seem to have a million different names, I mean steel cables that run from the corners of the bonnet to the roofline to...
  9. Range Rover Mark III / L322
    Its wet and cold outside today and I need to make a tool to remove the front upper arm suspension bush on my TD6. Does anyone have one close at hand and could they please measure the o/d preferably in metric so I can start to make the tool. Or the i/d of the arm Thanks Adrian
  10. Range Rover Mark II / P38
    I've a 1996 4.6 hse with a bad wobble on rear when breaking, especially from around 65 or 70 mph. Seems it could be the bushes as I replaced discs (rotors) and pads with no real improvement. Does this seem logical ? If so, I was wondering if anyone in U.K. supplies re bushed arms on an exchange...
  11. Range Rover Mark II / P38
    Will a bush bar from 2003-2005 model fit a p38? I can get one cheap locally but I can't find any info on anyone doing this install before.
  12. Range Rover Mark III / L322
    I changed my bushes and ball joints on the front of the range rover today. Rave shows using a cup and threaded rod or bolt to pull the new bush in to the arm. I cut the old bush out, no problem I thought. I had some lumps of round bar stock which fit the bill perfectly. So I proceeded to try...
  13. Range Rover Mark II / P38
    Hi, I have a slight steering wobble felt at around 60 KMPH. I checked under the car & found that bushings of rear radius arms are damaged (missing collar like portion). These are orange colour polybushes. Front ones are fine , replaced about 2 months ago with blue colour poly bushes. Can...
1-13 of 15 Results
Top