Range Rovers Forum banner

bracket

  1. Range Rover Mark IV / L405
    To make a long story short, my truck is in the shop for a few things including replacing the "Front Radar Sensor Control Module Mounting Bracket". The dealership service advisor told me they can not find a part number for it, so had to take picture of the broken one and send to headquarters to...
  2. Range Rover Sport II / L494
    There is a bracket available for the 2014-2017 MY RRS: https://bigmikesperformanceparts.com/2014-2017-range-rover-sport-sns55/ But I haven't found one for the 2018+ yet. For those of you in states that require a front plate what have you done? Drilling into the bumper just feels wrong. I live...
  3. Range Rover Sport / L320
    Moved to TX and have to have two plates. Dealer has only flat plate to drill into painted bumper. I've seen these on vehicles and the ones I asked in traffic said "I got it at the dealer" but traffic moved before I found out what dealer. Anybody have a source?
  4. Range Rover Classic
    Does anyone know the part number or a source (new or used) for the front fender angle mounting bracket? I need a RH one as mine got a little holey after blasting.
  5. Range Rover Mark III / L322
    Can you help me identify where this bracket bolts to? I found it in the floor among other bolts and screws. thanks!
  6. Range Rover Mark III / L322
    question for the experts here... I have a broken motor mount bracket. is there anyway to change that doesnt involve separating body from frame? I have the 4.4 jaguar motor.. 2006 thanks for any input
  7. Range Rover Mark III / L322
    Last weekend I sprung a coolant leak. Thank goodness it started steaming at the foot of my driveway after running around all morning. I drove it up to the garage and parked it outside until it cooled off and stopped leaking, and then put her in. I ordered a Stant 122270 Coolant Pressure Testing...
  8. Range Rover Mark III / L322
    Sooooo the wife hit something (she doesn't know what :roll:) and broken the bracket that holds the deployable side step to the pivot on the rod. I saw the step hanging down and went to examine it. She must of hit a curb or something pretty high to smack this bracket enough to break it. Or was...
  9. Range Rover Mark III / L322
    Hey guys, wrapping up a timing chain job, and I have this last bracket that I cannot figure out where it goes. Please have a look and let me know if you know where this sucker goes. It looks fairly an important, but I am a stickler. Any help is appreciated, thanks.
  10. Range Rover Mark II / P38
    Does anyone know the purpose of this bracket over the nut/bolt that holds the front panhardrod to the chassisrail? It's in the way, I want to renew the bushings of that rod.
  11. Range Rover Mark III / L322
    How do I buy those little rubber mounts the engine cover attaches to in the back bracket? Are they included in the bracket I don't see a broken out number.
  12. Range Rover Mark III / L322
    Hello all, I removed my driver's door (LH) panel recently and found several clip brackets falling off the door panel. Maybe I pried at the wrong point, but anyway... I can't tell what adhesive was used to glue the brackets to the back side of the door panel, but I think I'm supposed to glue...
  13. Range Rover Sport / L320
    I have in the picture below a bracket from my 2008 and what was supposed to be the replacement. As you can see its not the right size replacement. What do I need to actually order? I ordered what was supposed to be right for a 2008 rrs hse. This is for the right rear side.
  14. Range Rover Mark III / L322
    I'm trying to separate the motor from the bracket on the passenger side step on my car. I've looked at it from all angles, removed all bolts but cannot see how to separate the motor spindle off the bracket other than brute force. It still feels solid. It probably isn't helped by the corrosion...
  15. Range Rover Mark III / L322
    Can someone tell me the specifics on the caliper bracket mounting bolt? I'm terrible metric conversion & I don't have a parts manual or breakdown I know its close to 1/2-20 X 1-5/8 but that's useless info I'm guessing M12 but don't know the pitch & don't believe length is 42mm Help please
  16. Range Rover Mark III / L322
    so...in an attempt to ensure everything is nice and tight under the hood, I overtightened the bolt and it snapped off. I am having a great time trying to find the part online. what the deuce did I do? anyone know the part#?? here is a pic. this is from my '03 rr
  17. Range Rover Mark III / L322
    I'm guessing that the rubber mounting bushes should be connected to the reservoir ? If so ....Anyone know where I can get these bushings from please ?
  18. Range Rover Mark II / P38
    Rear Bumper Support Bracket Clip & Suspension Air Reservoir Queries The rear bumper side support brackets and clips on my model year 2000 HSE 4.0 are pretty much completely rusted away. Can see some little stubs of clip in the nylon carriers on the bumper but no sign of the brackets except for...
  19. Range Rover Sport / L320
    Need a bit of help getting the wheel nuts, caliper bracket, and rotor off... Hello, Attempting to help a friend save a bit of money by changing his pads and disks. Done it a hundred times on BMWs but looks like there are a few gotchas (aka I will never buy a Range, too spoiled by the logic of...
  20. Range Rover Mark II / P38
    I am in the process of fabricating a vertical, spare wheel bracket to mount in the left side of the P38 load space. I have a donut 90 litre LPG tank in the spare wheel well and have driven for some time without a spare wheel on short trips and for long trips I just stood it on the floor behind...
Top