RangeRovers.net Forum banner

bolts

  1. Window Regulator bolts red locktite

    Range Rover Sport / L320
    Anyone know why the window regulator bolts have red locktite on them? I was replacing the failed door latch and while removing the window regulator for access I stripped out one of the threaded inserts because the bolts have red locktite. It just spins and spins and I can not remove the bolt...
  2. 2009 L322 SC Autobiography Brembo Caliper Bolts falling out

    Range Rover Mark III / L322
    Has anyone else had the two big bolts that hold the brake caliper to the axle fall out? I lost one about 2000 km ago and had it replaced then today the other one fell out, stripping the threads as it left. No brake work done recently so I can't understand why they would suddenly loosen.
  3. exhaust manifold bolts

    Range Rover Mark II / P38
    1998 4.6L Gems One of my exhaust manifold to head bolts sheared, and so I thought I may as well replace the whole set of 8. But everywhere i look they reference a 12 point M8 bolt ERR4961. But mine are 12 point and M10 - there's no sign anyone ever drilled out from 8mm to 10mm, although this...
  4. L322 Vogue DVD Chassis bolts

    Range Rover Mark III / L322
    Does anyone happen to know the size of the bolts that hold the GPS DVD Chassis in the frame in the boot. I’ve managed to drop a couple whilst removing it
  5. Rear Seat Mounting Bolts

    Range Rover Classic
    Just wrapping up a very extensive, year-long process to fix all the rust and paint the floor of my 92 RRC. In the process of putting the interior back together and specifically the rear seats. I broke a few of the floor mounting (10mm) bolts off during the removal of the seats and now I am in...
  6. Front seat bolts

    Range Rover Classic
    After fixing the power seat switches and getting them working again, I noticed the seat bolts at the back of the tracks for my front seats are missing. I have one bolt at the front of each track, but the rear is loose and I can tilt the whole seat forward if I loosen the front bolts. Does...
  7. T-50 Torx Bolts for Lower Front Suspension Ball Joint

    Range Rover Mark III / L322
    Where do you get these bolts? The lower ball joints did not come with new ones, which is unacceptable considering they appear to be torque-to-yield and are all deformed when you remove them. I can't find these bolts on any of the parts websites. Below is the RAVE photo of what I'm talking...
  8. Need part numbers for front suspension bolts

    Range Rover Mark III / L322
    Hi. I a man replacing the front upper and lower control arms, upper ball joints, and sway bar on my 2006 HSE. i can find component part numbers but not the bolts that they recommend to replace, as they are stretched after being torqued. Does anyone have these part numbers? Upper control arm...
  9. Corroded sway bar bolts 13 RRS SC

    Range Rover Sport / L320
    Has anyone had this issue? The bolts that hold the sway bar are corroded and will not come off. They have been heated, oiled, lubed, everything. I have had 2 places tell me my only option is to remove the engine or drop the subframe. Engine removal is not an option as I am not dumping 4k for a...
  10. valve cover bolts and grommets

    Range Rover Sport / L320
    Hi I have a 2006 RRS SC. I'm confused about the valve cover bolt grommets. There is a kits that has PART # 4728385 , 4536846 x14 PART # 4728386 , 4536847 x8 PART # 4728387 , 4568726 x2 That makes a total of 24 parts , but its not clear which one goes in which hole ? I didnt keep track when...
  11. 2011 RRS - TORQUE SPEC FOR COOLANT PUMP BOLTS

    Range Rover Sport / L320
    I do not have a Shop Manual, so would someone advise the correct torque setting for the four Torx bolts that secure the Coolant Pump to the Timing Cover. My engine is a 5.0 WITHOUT Supercharger. Thanks much! usmcfred
  12. 4 bolts that hold dash to bulkhead. Part number?

    Range Rover Mark II / P38
    There are 4 bolts that connect the dash frame to the bulkhead down in the footwells. Does anybody know the part number? I've been going through the parts catalog and I'm not finding it. In the picture it would be the one circled in red. Thank you
  13. Where to buy strut knuckle bolts?

    Range Rover Mark III / L322
    Anyone know where I can get the new strut bolts in the strut and knuckle which are 22mm? Can I just go to the hardware store and get some or do I have to order oem ones? I am having trouble finding them. Those 2 bolts are a pain in the butt to remove and I messed up the threads on one of them.
  14. why do flywheel and torque convertor bolts need replacement?

    Range Rover Evoque / L538
    Hi! This is my first post on this forum. My brother took his 2013 Evoque in for service and the dealer came back with a long list of things that need to be done including replacing flywheel and torque converter bolts. I've never encountered this in any of the cars I've had. Is this a common...
  15. 95 SWB, rear output flange, studs or bolts?

    Range Rover Classic
    I changed the ATF in my transfer box today and happened to notice that the transmission brake drum had a bit of movement in it, so I picked up the rear axle and rotated the rear propshaft by hand and discovered all 4 nuts were loose and the bolts/studs were spinning freely when I tried to...
  16. RRC Exhaust Manifold Bolts Coming Loose

    Range Rover Classic
    The RAVE manual claims there should be lock tabs on these bolts... I don't have a lock tab (must have been removed by previous owner). Upon some internet scouring, the stock lock tab system is claimed to be worthless. What is the recommended route here? I've heard both loctite and lockwashers...
  17. Rocker bolts snapped - dodgy torque wrench?

    Range Rover Mark II / P38
    Hi all Returning the car today I went to bolt the rockers on and two of the bolts sheered off, one on either side. After the first one, I found that there was some oil in bottom of the threads I hadn't cleaned out, so assuming that was the cause I made extra sure the threads on the other head...
  18. Caliper to Hub Bolts

    Range Rover Mark III / L322
    So just a quick question pertaining to a 2006 range rover n/a 4.4 (so regular sliding calipers front and back). The, I presume torque to yield, calipers bolts that your replace every time you take them out, not the ones on the back of the slide pins, the ones for the caliper mount bolt that...
  19. What size bolts for front bump stop?

    Range Rover Classic
    My 1986 RR just failed it's annual inspection on a missing front bump stop . I now have the part but I am not sure what size bolts it needs. It's the 4 hole type, part number ANR4188. Any idea?
  20. are the head bolts on a 95 classic 4.2 stretch bolts?

    Range Rover Classic
    I have a driver's side gasket weeping and I'm going to fix it before it gets worse. Are the bolts stretch bolts? Can they be reused if not?
Top