Range Rovers Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-18 of 70 Results
  1. Range Rover Mark II / P38
    Hello all Range rover p38 4.6 GEMS 1996 Can anyone help and know the correct length of the single flanged bolt which holds the fan belt tensioner to the alternator bracket Took the tensioner off and some cowboy had fitted an helicoil in the bracket, which came out with the bolt. Panic at first...
  2. Range Rover Mark II / P38
    I have a leak through the front outside rocker cover bolt on the right hand side of the car. Did some research, tried tighten the bolt up a bit as it was quite loose, having tightened it unfortunately it still leaks. Pretty quickly too, started the car and within a minute or two I can see some...
  3. Range Rover Sport / L320
    hey friends - so my 06 RRS HSE has been having C1A13 and C1A20 codes - sometimes going down to the bump stops. i replaced the dryer and also decided to do the valve repair kit while i had the compressor out. while trying to take off the 17mm bolt to access the spring on the compressor, it...
  4. Range Rover Mark III / L322
    Here's one for the experts - what size 12-point socket fits the caliper holding bolts on a Ranger Rover L322 MY2010? The vehicle is on jacks; I have a 20mm and 21mm combo-wrench and the 20mm is too small and the 21mm is loose. Could it be Imperial? I thought the bolt was M12. Thanks.
  5. Range Rover Mark III / L322
    I have a 2012 Range Rover Supercharged. I have some front wheel vibration when i brake over 50mph. I posted on some forums and got feedback that I may need to replace my front rotors. Did some research and ordered new front brake pads and rotors. I jacked up the car today to find out that the...
  6. Range Rover Sport / L320
    Found this lil guy stuck in some of the chassis rails below the engine. I don't recall working on or removing this type of bolt. Curious if any of you pros know where it may have run away from. Thanks!
  7. Range Rover Mark III / L322
    After overhauling the gearbox I managaed to cross thread the last bolt on the tc. 2002 l322 v8 vogue. What’s the best way to proceed? Can it be helicoiled in place? Without removing the flex plate?
  8. Range Rover Mark III / L322
    Here is a strange one. Doing the rear brakes on my 2007 RR SC. One wheel jacked, car in neutral. Parking brake adjuster backed all the way out. Hub will spin with some effort when rotor is not on. Same with rotor resting on lugs. Same with rotor retaining screw/bolt slightly loose. Once...
  9. Range Rover Mark II / P38
    Something missing? Don't think LR would just have a bolt hanging out of the block by itself. And looking on the net cant find a good pic.
  10. Range Rover Evoque / L538
    Engine malfunction light came on-service said just needed software update-that didn't work-then they said cam bolt broke-been in shop almost 2 weeks-timing correlation fault. What's up?
  11. Range Rover Mark III / L322
    Hi there i am having an issue with my 2003 L322, my issue is with the lower tailgate where the center latch pin where the latch from the upper tailgate locks onto, there seems to be 2 screws/bolts that should keep the pin secure but one is missing and the second one has become loose, i am...
  12. Range Rover Mark III / L322
    2003 RR 4.4L. I had to change the alternator which went smoothly. When I put the tensioner bolts back in, the one on the right that is to tighten and hold the bracket would not bottom out and I could not get the tensioner to hold against the belt. When I took the bolt back out, it had what looks...
  13. Range Rover Mark III / L322
    2006 RR HSE I went to change a couple of my ignition coils but one of them has a bolt that turns but doesn't come up. Before coming up with an idea(that usually cost me more money) I thought I would check to see what others have done in this situation. It will turn and turn but don't come up...
  14. Range Rover Sport / L320
    Drained the front transfer case, gosh my S7 mangled my thread title. I got the brown mud out, it was awful, but I can't tell which bolt is for filling. Anybody know?
  15. Range Rover Classic
    I am trying to find a replacement bolt for the two rear bolts on the passenger side of the exhaust manifold. They are odd looking bolts that attached the exhaust manifold to the block, and also separate the heat shield from the manifold and attach the heat shield. I know that I am not...
  16. Range Rover Mark III / L322
    I started my VANOS a while ago, but with my hectic schedule I just got to the VANOS itself. Now, tried undoing the exhaust sprocket and couldn't budge it with a 2ft breaker bar and a 3ft PVC "extension." Put some AeroKroil on it but there's not really anywhere for the stuff to work. The actual...
  17. Range Rover Mark II / P38
    Transmission oil change- broken pickup tube & broken bolt I took on the task of draining and replacing my transmission fluid. My shifter was a little tight and I just purchased my P38 at 162k and it didn't seem taken care of. The manual says it needs to be changed at 100k and I was doubtful it...
  18. Range Rover Classic
    I have a 95 classic with serpentine belt 4.2. Is a 98 4.6 a straight bolt in swap or does the transmission have to be changed as well? Other than swapping engines, what can be done to get more power from a 4.2?
1-18 of 70 Results