RangeRovers.net Forum banner

blend

  1. Heat blend motor problem

    Range Rover Mark II / P38
    Hi all...trying toget through a list of little annoyances on my 51 Westminster.. This week its the heat control motors The original had stripped gears so I picked one up from fleabay. I have the feeling it has been repaired and wonder if anyone has a picture of the timing of the gears / pot on...
  2. HVAC blend motor plug

    Range Rover Mark II / P38
    Hi I replaced the blend motors in my P38 and at he same time replaced the HVAC dash control unit to fix a display problem. But ... I cannot get the multiple to go into the top of the HVAC unit, it will just not clip down and I cannot find out why. I even changed the multi plug over to another...
  3. My blend motor is short to positive

    Range Rover Mark II / P38
    I am trying to access it but on the drivers side (USA) the duct is in the way. Someone cut the duct and taped it it but I can't get it out, anyone know a trick? THX:shock:
  4. Anyone in Yorkshire replace blend motors?

    Range Rover Mark II / P38
    Hi All, is there anyone local to Leeds who is willing to replace the blend motors on my 1999 4.6? I'm fairly DIY competent but don't have the time... Obviously I'll pay!
  5. HVAC blend motors

    Range Rover Mark II / P38
    Hi guys I have a issue with my heating not very hot on one side , there is lots of infomation on here about the blend motors etc, this I will use next week when I look into the job, the thing I need info about is the blend motors, I though there was two, one on each side, but they are...
  6. blend motors

    Range Rover Mark II / P38
    I've lashed out and bought a group of three blend motors to replace the two duds in my car. From reading the sticky etc. I am working on the understanding that I need to remove the centre console piece of plastic and the piece of plastic under the steering wheel and then get into the duct...
  7. Replacement Heater Blend servos don't fit

    Range Rover Mark II / P38
    Hello all, Just finished doing the heater core o-ring to Audi heater core conversion. I went the full route and removed the dash so that I could also service the heater box and blend servos while I was there. The problem I'm having is the replacement servos don't fit in their receptacles...
  8. Blend motor gear timing

    Range Rover Mark II / P38
    Happy Christmas all.. I thought id spend some free time fixing the passenger blend motor problem on my 51 plate. The motor wasnt turning at all so picked up a second hand one from fleabay. On inspection the replacement motor had teeth broken so ive swapped gears from the original but im not...
  9. How do you confirm if heater blend motors are working

    Range Rover Sport / L320
    Hello All, I am wondering how to confirm which blend motors are working correctly? After some research I'm pretty sure it is my heater core that is causing me to have no heat on drivers side while having heat on passengers side however I better confirm that the heater blend motors are...
  10. Hvac blend door motors

    Range Rover Sport / L320
    Does anybody know how many blend door motors in the sports model?
  11. Blend door rebuildable gears

    Range Rover Mark II / P38
    Hey all, I am suffering from the usual testbook symbol blend door (stc3259) issues on my range rover. I am in contact with a manufacturer who currently makes replacement blend door and window lift gears for other makes. I am sending him my faulty actuator and he will attempt to build a prototype...
  12. Blend motor for vent directions

    Range Rover Mark II / P38
    P38, 2001, 110K miles Air vent control direction will not change, so assuming the blend motor for the central flap is kaput. Can I use any motor from the set of three that come together. STC3259? I have one spare motor from the original set of three I purchased and I can't recall if this...
  13. quick blend motor replacement

    Range Rover Mark II / P38
    Hi with new blend motors now being becoming affordable I am sure this might be considered useful info not sure if anyone has posted this but I have discovered that it is possible to replace blend motors without cutting wires or removing and re-inserting connector pins mind you this only...
  14. Another blend motor question

    Range Rover Mark II / P38
    Hello, I have a 2000 4.6 HSE Rhino edition p38. U.S. Model. Air conditioning, of course. (I only mention that because from what I read, there are different procedure for A/C and non A/C cars) I bought it about 1 1/2 years ago and have been fixing things here and there. The previous owner told...
  15. Blend door help

    Range Rover Mark II / P38
    Hey guys. Been searching and searching and can't find too much. Obviously there is a TON on blend doors, but I'm hoping someone can chime in. I've got no control over where the air is directed, I've gone ahead and given myself access to the blend doors. If I pull the fuse and reset everything I...
  16. Blend Motor Question

    Range Rover Mark II / P38
    Is the blend motor plug shown in this photo at the back of the hevac panel the same plug as the plug in the second photo? If so is it possible to unplug the blend motors in the car and plug a set of three in for testing in it's place? Just to check they are working properly before stripping...
  17. Possible blend motor issue ugh

    Range Rover Sport / L320
    In my 06 rrs supercharged I have heat everywhere but when I turn ac on i only get it on the drivers side, the passenger side just blows heat. This goes for front and back, ac or heat on drivers side and only heat passenger side. Is this definitely a blend motor, or could it be the dual zone...
  18. blend motors original or after market

    Range Rover Mark II / P38
    hi to all and thanks in advance for all comments the other day I had a over heating issue on the inside, 30 degrees outside with the heater stuck on on the inside, having to leave the windows up so as to not have the roof lining flapping around leaving sticky crap every where, it was warm ha...
  19. Blend Motor?

    Range Rover Mark II / P38
    Hi Just recently I've been getting a fault on the HEVAC. On my Nanocom it reads as "The Left hand blend motor is short circuit to positive". Does this mean a stuck blend motor (mechanically) or an electrical problem? Thanks
  20. Blend Motor Help

    Range Rover Mark II / P38
    Hello All, I am replacing the blend motors in my 2002 RR P38A LHD. Apparently, they have been replaced before. The right side of the blend motor wiring is color-coded with tape, one wire taped gray, and the other blue. Although the old and new bundles of three blend motors are both Valeo...
Top